61805-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61805-NSK model number is decoded

61805 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 05 by five gives the 25 mm bore; the 37 mm outside diameter and 7 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 25 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 25 mm shaft for 61805 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• Only 6.0 mm of radial section separates bore and OD on the 618xx series at 25 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6205.
• Storage matters for open bearings: 61805-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61805 units.
• Shaft and housing fillets must clear the bearing chamfer so the 7 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• The open 61805 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 25 mm bore puts 61805 in NSK's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty. NSK's VV non-contact seal is the high-speed choice here — DDU contact seal costs roughly 30–40% of the open-bearing speed ceiling.
• At 4.95 kN dynamic load rating (C) and 3.15 kN static (C0), 61805 is a light-load NSK bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 21 g, 61805 is a lightweight NSK bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 25×37×7 mm envelope of 61805 gives a D/d ratio of 1.48 and 6.0 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 4.95/3.15 kN load ratings, mass 21 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6805 on the 25×37×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61805 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK's VV non-contact seal keeps frictional torque close to the open 61805; in motor duty where heat build-up matters, VV is the usual compromise between debris protection and speed capability.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.