61805-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61805-NTN model number is decoded

61805 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 05 by five gives the 25 mm bore; the 37 mm outside diameter and 7 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 25 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• A 25 mm shaft for 61805 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
• The 618xx thin section at 25 mm bore has only a 6.0 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6205.
• Storage matters for open bearings: 61805-NTN leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61805 units.
• Shaft and housing fillets must clear the bearing chamfer so the 7 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• The open 61805 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 25 mm bore puts 61805 in NTN's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• NTN rates 61805 at 18000 r/min grease limiting speed — this is a high-speed electric-motor range; keep the grease fill at 20–30% of the free bearing volume and avoid mixing grease thickener types if regreasing through the housing.
• At 4.75 kN dynamic load rating (C) and 2.95 kN static (C0), 0.21 kN fatigue load limit Cu, 61805 is a light-load bearing: the L10 life at catalogue C is short above a few kN of equivalent load, so size up to a 62-series on the same bore if the application sees shock or frequent starts.
• At only 22 g, 61805 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 25×37×7 mm envelope of 61805 gives a D/d ratio of 1.48 and 6.0 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 4.75/2.95 kN load ratings, 0.21 kN fatigue load limit Cu NTN lists the grease limiting speed at 18000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 22 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6805JR on the 25×37×7 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61805 in a rated drive.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61805 is listed.
• Order the C3 internal-clearance version (61805 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.