61815-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61815-RSR-NTN model number is decoded

61815-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 15 by five gives the 75 mm bore; the 95 mm outside diameter and 10 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 75 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6815LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 75 mm bore, induction heating to roughly 80–100 °C is the clean mounting method; never exceed 120 °C, and hold 61815 against the shaft shoulder while it cools so the ring cannot creep back.
• The 618xx thin section at 75 mm bore has only a 10.0 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6215.
• The low-drag lip of 61815-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 61815-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 75 mm bore position before relying on it as sealed-for-life.
• Never mix components between two 61815-RSR-NTN units: rings, cage and balls are factory-matched and are not field-interchangeable, even between identical designations.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 10 mm-wide ring of 61815-RSR-NTN drags the lip and overheats it.
• NTN catalogues this low-friction non-contact seal as 6815LLB (suffix LB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 75 mm bore 61815 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 6400 r/min the grease limiting speed for 61815 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• NTN rates 61815 at 13.9 kN dynamic (C) and 12.9 kN static (C0), 0.85 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 145 g, 61815 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 75×95×10 mm envelope of 61815 gives a D/d ratio of 1.27 and only 10.0 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 13.9/12.9 kN load ratings, 0.85 kN fatigue load limit Cu NTN lists the grease limiting speed at 6400 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 145 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6815LLB on the 75×95×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61815 in a rated drive.
• Order the C3 internal-clearance version (61815 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.