61821 bearing: complete specifications & equivalents
The 61821 is a ISO 15 radial bearing sized 105 x 130 x 13 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 105 mm |
| Outer diameter D | 130 mm |
| Width B | 13 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 20.8 kN |
| Basic static load rating C0 | 19.6 kN |
| Fatigue load limit Pu | 1 kN |
| Reference speed (thermal) | 10000 rpm |
| Limiting speed (mechanical) | 6300 rpm |
| Operating temperature | -40 to +150 °C |
| Mass | 310 g |
| Manufacturer designation | SKF 61821 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61800-series range
| Bore d | 4.134 in |
|---|---|
| Outer diameter D | 5.118 in |
| Width B | 0.512 in |
| ISO bore code | 21 |
| Radial section height (D−d)/2 | 12.5 mm |
| Smallest bore in 61800-series | 10 mm |
| Largest outer diameter in 61800-series | 420 mm |
| Width range across 61800-series | 5–38 mm |
| Bore position in 61800-series (smallest first) | 22 of 39 |
| Bore above smallest 61800-series size | 95 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61821-ZZ | GENERIC-ISO | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 105×130×13 mm envelope per ISO 15; seal variant differs (OPEN vs ZZ) — confirm sealing suits the duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61821 model number is decoded
In the 61800-series (ISO 15 diameter series 8) the last two digits encode the bore: 61821 carries bore code 21 = 105 mm. Outside diameter 130 mm and width 13 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 105 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- packaging machinery
- space-constrained gearboxes
- clutch and transmission assemblies
- robotics and automation joints
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- brinelling from static overload or hammering during mounting
- false brinelling from vibration while the shaft is stationary
Selection pitfalls — read before you substitute
- Mount this 105 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 618xx thin section at 105 mm bore has only a 12.5 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6221.
- The open 61821 has no lubricant retention: grease escapes and contaminants migrate straight into the 105×130×13 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61821 units.
- Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
- The open 61821 needs external sealing and application-supplied lubrication; in the SKF catalogue the protected variants are separate order numbers 61821-2Z (shields) and 61821-2RSH (contact seals), not suffix-free 61821.
- The 20.8/19.6 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61821 bearing?
A 61821 deep-groove ball bearing has a 105 mm bore, 130 mm outer diameter and 13 mm width (4.134 × 5.118 × 0.512 in), per ISO 15 boundary dimensions. It is an open bearing with no seals or shields.
How does the 61821 bore code work?
The last two digits of 61821 are bore code 21, giving 21 × 5 = 105 mm bore. The 130 mm outside diameter and 13 mm width follow the ISO 15 diameter series, not the bore code alone.
What does no suffix on 61821 mean?
A bare 61821 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication.
How does the 61800 compare with other series at the same 105 mm bore?
618 is an extra-thin section: 130×13 mm, only 12.5 mm radial section at 105 mm bore, far smaller than a 6221, for space-limited layouts at the cost of load rating and misalignment tolerance.
What is the SKF designation and catalogue data for 61821?
In the SKF Rolling Bearings catalogue this size is listed as 61821 — the open (unsealed) execution, 105×130×13 mm per ISO 15. Quoted values: C 20.8 kN, C0 19.6 kN, Pu 1 kN, limiting speed 6300 r/min, mass 310 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61821.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.