61824-ZZ bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61824-ZZ model number is decoded

61824-ZZ carries two non-contact sheet-steel shields that hold the factory grease in and keep coarse debris out; they do not seal against liquids. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 24 by five gives the 120 mm bore; the 150 mm outside diameter and 16 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 120 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK catalogue order number: 6824ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 120 mm of 61824-ZZ demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• Only 15.0 mm of radial section separates bore and OD on the 618xx series at 120 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6224.
• ZZ shields are non-contact: 61824-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 61824-2RS for that.
• Do not wash 61824-ZZ in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 61824-C3. No clearance suffix means normal CN clearance.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• NSK catalogues the shielded version as 6824ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NSK order number when buying through an NSK channel.
• At 120 mm bore 61824 is in NSK's medium industrial range; the pressed-steel cage is standard, but large-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• At 32 kN dynamic load rating (C) and 35.5 kN static (C0), 61824 is a medium-load NSK bearing suitable for most electric-motor and pump duty; the C0/C0r ratio matters for preloaded or thrust-loaded arrangements, so confirm the static safety factor with the NSK catalogue.
• At 537 g, 61824 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 120×150×16 mm envelope of 61824 gives a D/d ratio of 1.25 and only 15.0 mm radial section height — this is an ultra-thin section in NSK's E1103 catalogue where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 32/35.5 kN load ratings, mass 537 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6824ZZ on the 120×150×16 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61824 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.