61824-RSR bearing: complete specifications & equivalents
The 61824-RSR is a ISO 15 radial bearing sized 120 x 150 x 16 mm (bore x OD x width) with RSR sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 120 mm |
| Outer diameter D | 150 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | RSR |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 29.1 kN |
| Basic static load rating C0 | 28 kN |
| Fatigue load limit Pu | 1.29 kN |
| Reference speed (thermal) | 8500 rpm |
| Limiting speed (mechanical) | 4300 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 650 g |
| Manufacturer designation | SKF 61824-2RZ |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61800-series range
| Bore d | 4.724 in |
|---|---|
| Outer diameter D | 5.906 in |
| Width B | 0.63 in |
| ISO bore code | 24 |
| Radial section height (D−d)/2 | 15 mm |
| Smallest bore in 61800-series | 10 mm |
| Largest outer diameter in 61800-series | 420 mm |
| Width range across 61800-series | 5–38 mm |
| Bore position in 61800-series (smallest first) | 24 of 39 |
| Bore above smallest 61800-series size | 110 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61824-ZZ | GENERIC-ISO | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 120×150×16 mm envelope per ISO 15; seal variant differs (RSR vs ZZ) — confirm sealing suits the duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61824-RSR model number is decoded
In the 61800-series (ISO 15 diameter series 8) the last two digits encode the bore: 61824 carries bore code 24 = 120 mm. Outside diameter 150 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 120 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- robotics and automation joints
- lay shafts and idler shafts
- textile machinery
- packaging machinery
Known failure patterns
- ingress of fine dust or moisture past the non-contact lip in dirty or wet duty (RSR is not liquid-tight)
- lip-lubricant starvation if the bearing runs dry for extended periods
- electrical pitting in VFD-driven motors without grounding protection
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Mount this 120 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 618xx thin section at 120 mm bore has only a 15.0 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6224.
- RSR low-friction seals on 61824-RSR run faster than contact-seal 61824-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 61824-2RS instead.
- The non-contact lip of 61824-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 120 mm bore position before relying on it as sealed-for-life.
- Suffixes stack in a defined order — clearance follows the seal code, e.g. 61824-C3. No clearance suffix means normal CN clearance.
- SKF catalogues the low-friction seal as 61824-2RZ (suffix -2RSL or -2RZ): a non-contact elastomer lip that runs near the open 4300 r/min limiting speed, closer to the open bearing's 8500 r/min reference than the contact-seal version. It keeps coarse debris out without the drag of a contact seal, but is not liquid-tight — use 2RSH for wet or fine-dust positions.
- The 29.1/28 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61824-RSR bearing?
A 61824-RSR deep-groove ball bearing has a 120 mm bore, 150 mm outer diameter and 16 mm width (4.724 × 5.906 × 0.63 in), per ISO 15 boundary dimensions. It is fitted with two low-friction non-contact rubber seals.
How does the 61824 bore code work?
The last two digits of 61824 are bore code 24, giving 24 × 5 = 120 mm bore. The 150 mm outside diameter and 16 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the RSR suffix on 61824-RSR mean?
RSR means two low-friction non-contact rubber seals. They keep coarse debris out with minimal drag (speed close to the open bearing) but are not liquid-tight; use -2RS contact seals for wet or fine-dust environments.
How does the 61800 compare with other series at the same 120 mm bore?
618 is an extra-thin section: 150×16 mm, only 15.0 mm radial section at 120 mm bore, far smaller than a 6224, for space-limited layouts at the cost of load rating and misalignment tolerance.
What is the SKF designation and catalogue data for 61824-RSR?
In the SKF Rolling Bearings catalogue this size is listed as 61824-2RZ — two low-friction non-contact elastomer seals, 120×150×16 mm per ISO 15. Quoted values: C 29.1 kN, C0 28 kN, Pu 1.29 kN, limiting speed 4300 r/min, mass 650 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61824-RSR.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.