61826-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61826-FAG model number is decoded

In the 61800-series (diameter series 8 of ISO 15) the last two digits encode the bore: 61826 carries bore code 26 = 130 mm. Outside diameter 165 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 130 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the Schaeffler HR 1 catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes 2Z (steel shields), 2RZ (non-contact rubber seals) and 2RSR (lip-contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 130 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• Only 17.5 mm of radial section separates bore and OD on the 618xx series at 130 mm: ring flex from clamping or an oval housing bore transfers straight into raceway stress, so seat roundness matters more here than on a 6226.
• The open 61826-FAG has no lubricant retention: grease escapes and contaminants migrate straight into the 130×165×18 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 61826-FAG leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Vibration during standstill brinells the raceways of a 130 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Shaft and housing fillets must clear the bearing chamfer so the 18 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• The open 61826 has no integral sealing; in the Schaeffler HR 1 catalogue the protected variants carry suffixes 2Z (two steel shields), 2RZ (two non-contact rubber seals) and 2RSR (two lip-contact rubber seals). Do not confuse FAG's 2RZ with a contact seal — the RZ lip does not touch the inner ring, which is why its speed capability stays close to the open bearing.
• At 5500 r/min mechanical limiting speed (thermal reference speed 3600 r/min), 61826 covers medium-duty industrial drives; the open or shielded execution can run continuously here on standard lithium grease.
• The 130 mm bore places 61826 at the lower end of Schaeffler's large-size range; at these diameters the pressed steel cage is speed-limited and FAG commonly offers a machined brass cage (suffix M) as an option. Verify cage material and relubrication provision with the distributor, and do not extrapolate small-bore speed ratings to this size.
• FAG rates 61826 at 37.7 kN dynamic (C) and 43 kN static (C0); this upper-medium rating covers conveyor and gearbox drives, but under shock the pressed steel cage can become the limiting element — consider the machined brass cage (suffix M) for impact duty.
• At 775 g, 61826 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 130×165×18 mm envelope of 61826 gives a D/d ratio of 1.27 and only 17.5 mm radial section height — an ultra-thin section in the HR 1 range where shaft deflection and housing ovality load the ball-raceway contact directly; verify shaft stiffness (target deflection under 0.05 mm) before choosing it over a 62-series.
• The 37.7/43 kN load ratings, mass 775 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 61826-FAG on the 130×165×18 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61826 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Schaeffler's medias/eKatalog is the live source for the current execution of 61826: cage material, seal lip design and ratings can be revised between catalogue generations without any designation change.
• FAG standard tolerance for this size is P0 (PN); P6/P5 precision executions exist for spindle-adjacent duty but carry different order numbers in the Schaeffler system — they are not a selectable sorting of standard stock.