61880 bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61880 model number is decoded

61880 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the extra-thin 618xx section (diameter series 8 of ISO 15), multiplying bore code 80 by five gives the 400 mm bore; the 500 mm outside diameter and 46 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 400 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 400 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 618xx thin section at 400 mm bore has only a 50.0 mm radial section height: it saves space but is highly sensitive to misalignment, shaft deflection and shock loads — verify shaft stiffness before choosing it over a 6280.
• The open 61880 has no lubricant retention: grease escapes and contaminants migrate straight into the 400×500×46 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 61800-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61880 units.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Measure the shaft, do not trust the drawing: a 400 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61880.
• The open 61880 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 400 mm bore places 61880 in NTN's upper maximum-size range; at this diameter the bearing mass is substantial and mounting requires induction heating of the inner ring (max 120 °C) with a mechanical puller. NTN supplies a machined brass cage (suffix M) and expects oil lubrication with a defined relubrication interval.
• NTN lists the grease limiting speed at 1100 r/min for 61880; this is a large-section size where the pressed-steel cage is speed-limited — NTN recommends the machined brass cage (suffix M) and oil lubrication for any continuous operation above this figure.
• NTN rates 61880 at 251 kN dynamic (C) and 340 kN static (C0), 10.6 kN fatigue load limit Cu; this is an upper heavy-load rating where the pressed-steel cage is not recommended — NTN supplies a machined brass cage (suffix M) and the static C0 must be verified against any shock or lifting loads the bearing sees during mounting.
• At 20600 g (20.6 kg), 61880 is a very heavy bearing where handling and mounting method directly affect service life; NTN requires induction heating of the inner ring (max 120 °C), a mechanical puller for removal, and a defined lifting procedure to avoid damaging the machined brass cage.
• The 400×500×46 mm envelope of 61880 gives a D/d ratio of 1.25 and only 50.0 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 251/340 kN load ratings, 10.6 kN fatigue load limit Cu NTN lists the grease limiting speed at 1100 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 20600 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6880 on the 400×500×46 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61880 in a rated drive.
• Standard catalogue stock of 61880 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61880 is listed.