61906-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61906-NSK model number is decoded

61906 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 06 by five gives the 30 mm bore; the 47 mm outside diameter and 9 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 30 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Sizes around 30 mm bore are normally pressed on cold with a sleeve against the inner-ring face; the press force must never route through the outer ring or the balls of 61906-NSK.
• The 619xx thin section (8.5 mm section height at 30 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• The open 61906-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 30×47×9 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Storage matters for open bearings: 61906-NSK leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Measure the shaft, do not trust the drawing: a 30 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61906-NSK.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 47 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 61906-NSK.
• The open 61906 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 30 mm bore puts 61906 in NSK's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty. NSK's VV non-contact seal is the high-speed choice here — DDU contact seal costs roughly 30–40% of the open-bearing speed ceiling.
• NSK rates 61906 at 7.95 kN dynamic (C) and 5 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At 52 g, 61906 is light enough for hand assembly but should be pressed on with a fitting sleeve against the inner ring; do not strike the outer ring or cage with a hammer.
• The 30×47×9 mm envelope of 61906 gives a D/d ratio of 1.57 and 8.5 mm radial section height — this NSK thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 7.95/5 kN load ratings, mass 52 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6906 on the 30×47×9 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61906 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 61906 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.