61906-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61906-RSR-NTN model number is decoded

61906-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 06 by five gives the 30 mm bore; the 47 mm outside diameter and 9 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 30 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6906LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At a 30 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 61906-RSR-NTN; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
• The 619xx thin section at 30 mm bore (8.5 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• The low-drag lip of 61906-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 61906-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 30 mm bore position before relying on it as sealed-for-life.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 47 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 61906-RSR-NTN.
• The housing bore for the 47 mm OD should be round within IT7; an oval bore pinches the outer ring of 61906-RSR-NTN and shows up later as two-point loaded raceway wear.
• NTN catalogues this low-friction non-contact seal as 6906LLB (suffix LB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• The 30 mm bore puts 61906 in NTN's light industrial range; the standard pressed-steel cage and CN clearance cover most fractional-horsepower motor and small-pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• At 10000 r/min the grease limiting speed for 61906 covers most general-purpose industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• NTN rates 61906 at 8 kN dynamic (C) and 5 kN static (C0), 0.36 kN fatigue load limit Cu; this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At only 48 g, 61906 is a lightweight bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 30×47×9 mm envelope of 61906 gives a D/d ratio of 1.57 and 8.5 mm radial section height — this thin section saves space but is sensitive to misalignment and shock; confirm the housing stays round within IT7 and the shaft does not deflect past the raceway contact angle under load.
• The 8/5 kN load ratings, 0.36 kN fatigue load limit Cu NTN lists the grease limiting speed at 10000 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 48 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6906LLB on the 30×47×9 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61906 in a rated drive.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 61906 is listed.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.