61909-2RS bearing: complete specifications & equivalents
The 61909-2RS is a ISO 15 radial bearing sized 45 x 68 x 12 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 45 mm |
| Outer diameter D | 68 mm |
| Width B | 12 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 14 kN |
| Basic static load rating C0 | 10.8 kN |
| Fatigue load limit Pu | 0.465 kN |
| Limiting speed (mechanical) | 6000 rpm |
| Operating temperature | -30 to +110 °C |
| Mass | 140 g |
| Manufacturer designation | SKF 61909-2RS1 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 1.772 in |
|---|---|
| Outer diameter D | 2.677 in |
| Width B | 0.472 in |
| ISO bore code | 09 |
| Radial section height (D−d)/2 | 11.5 mm |
| Smallest bore in 61900-series | 3 mm |
| Largest outer diameter in 61900-series | 1120 mm |
| Width range across 61900-series | 3–118 mm |
| Bore position in 61900-series (smallest first) | 17 of 63 |
| Bore above smallest 61900-series size | 42 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61909-2RS-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 61909-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 61909-RSR-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (2RS vs RSR) — confirm sealing suits the duty. |
| 61909-ZZ | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
| 61909-2RS-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 61909-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 61909-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (2RS vs RSR) — confirm sealing suits the duty. |
| 61909-ZZ-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (2RS vs ZZ) — confirm sealing suits the duty. |
| W61909-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 61909-2RS1 shares the 45×68×12 mm envelope but rates differently (14/10.8 kN vs 12.1/10.8 kN) — not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61909-2RS model number is decoded
61909-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 09 by five gives the 45 mm bore; the 68 mm outside diameter and 12 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 45 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. SKF's contact-seal catalogue number is 61909-2RS1 (older text: -2RS1), mapped here from the industry-neutral -2RS spelling.
Typical equipment & failure modes
Common applications
- clutch and transmission assemblies
- robotics and automation joints
- lay shafts and idler shafts
- textile machinery
Known failure patterns
- seal-lip hardening and loss of pre-grease in sustained high-temperature service
- grease-life expiry in the sealed-for-life cavity (no relubrication path)
- electrical pitting in VFD-driven motors without grounding protection
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 61909-2RS; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
- The 619xx thin section at 45 mm bore (11.5 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
- Contact seals add drag and heat: 61909-2RS runs slower and cooler-limited than the open 61909; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
- Never wash a sealed 61909-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
- Vibration during standstill brinells the raceways of a 45 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
- Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 12 mm-wide ring of 61909-2RS drags the lip and overheats it.
- SKF catalogues the contact-sealed version as 61909-2RS1 (older printings may read -2RS1); it is shipped pre-greased and its 6000 r/min limiting speed is set by seal-lip drag and grease life versus the open bearing's 20000 r/min thermal reference speed.
- The 14/10.8 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61909-2RS bearing?
A 61909-2RS deep-groove ball bearing has a 45 mm bore, 68 mm outer diameter and 12 mm width (1.772 × 2.677 × 0.472 in), per ISO 15 boundary dimensions. It is fitted with two contact rubber seals and is normally pre-greased.
How should 61909-2RS be mounted?
Apply the mounting force to the ring being fitted: on a 45 mm shaft seat the press load must pass through the inner-ring face only. A fitting sleeve and an arbor press are normally sufficient at this size. Never strike the outer ring, the cage or the seals.
What lubrication does 61909-2RS need?
61909-2RS is supplied pre-greased for life and is not designed to be opened for relubrication; where a relubrication path is required, specify the open 61909 with a housing grease fitting instead.
How does the 61909 bore code work?
The last two digits of 61909 are bore code 09, giving 09 × 5 = 45 mm bore. The 68 mm outside diameter and 12 mm width follow the ISO 15 diameter series, not the bore code alone.
What is the SKF designation and catalogue data for 61909-2RS?
In the SKF Rolling Bearings catalogue this size is listed as 61909-2RS1 — two contact elastomer seals over a lifetime grease fill, 45×68×12 mm per ISO 15. Quoted values: C 14 kN, C0 10.8 kN, Pu 0.465 kN, limiting speed 6000 r/min, mass 140 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61909-2RS.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.