61909-RSR bearing: complete specifications & equivalents
The 61909-RSR is a ISO 15 radial bearing sized 45 x 68 x 12 mm (bore x OD x width) with RSR sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 45 mm |
| Outer diameter D | 68 mm |
| Width B | 12 mm |
| Material | GCr15 |
| Seal / shield | RSR |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 14 kN |
| Basic static load rating C0 | 10.8 kN |
| Fatigue load limit Pu | 0.465 kN |
| Reference speed (thermal) | 20000 rpm |
| Limiting speed (mechanical) | 10000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 140 g |
| Manufacturer designation | SKF 61909-2RZ |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 1.772 in |
|---|---|
| Outer diameter D | 2.677 in |
| Width B | 0.472 in |
| ISO bore code | 09 |
| Radial section height (D−d)/2 | 11.5 mm |
| Smallest bore in 61900-series | 3 mm |
| Largest outer diameter in 61900-series | 1120 mm |
| Width range across 61900-series | 3–118 mm |
| Bore position in 61900-series (smallest first) | 17 of 63 |
| Bore above smallest 61900-series size | 42 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61909-2RS-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (RSR vs 2RS) — confirm sealing suits the duty. |
| 61909-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (RSR vs OPEN) — confirm sealing suits the duty. |
| 61909-RSR-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 61909-ZZ | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (RSR vs ZZ) — confirm sealing suits the duty. |
| 61909-2RS-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (RSR vs 2RS) — confirm sealing suits the duty. |
| 61909-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (RSR vs OPEN) — confirm sealing suits the duty. |
| 61909-RSR-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 61909-ZZ-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×68×12 mm envelope per ISO 15; seal variant differs (RSR vs ZZ) — confirm sealing suits the duty. |
| W61909-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF stainless execution W 61909-2RS1 shares the 45×68×12 mm envelope but rates differently (14/10.8 kN vs 12.1/10.8 kN) — not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61909-RSR model number is decoded
61909-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the thin 619xx section (diameter series 9 of ISO 15), multiplying bore code 09 by five gives the 45 mm bore; the 68 mm outside diameter and 12 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 45 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. SKF's low-friction seal suffix is 2RSL/2RZ (this page's industry-neutral spelling is -RSR); catalogue number 61909-2RZ.
Typical equipment & failure modes
Common applications
- lay shafts and idler shafts
- textile machinery
- packaging machinery
- space-constrained gearboxes
Known failure patterns
- ingress of fine dust or moisture past the non-contact lip in dirty or wet duty (RSR is not liquid-tight)
- lip-lubricant starvation if the bearing runs dry for extended periods
- brinelling from static overload or hammering during mounting
- false brinelling from vibration while the shaft is stationary
Selection pitfalls — read before you substitute
- A 45 mm shaft for 61909 should be finished to Ra ≤ 1.6 µm with square seating faces; at this bore a scored or oval journal shows up directly as running noise and early raceway damage.
- The 619xx thin section (11.5 mm section height at 45 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
- The low-drag lip of 61909-RSR barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
- The non-contact lip of 61909-RSR does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 45 mm bore position before relying on it as sealed-for-life.
- Deep-groove ball bearings tolerate only minutes of misalignment; if the 68 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 61909-RSR.
- Measure the shaft, do not trust the drawing: a 45 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61909-RSR.
- SKF catalogues the low-friction seal as 61909-2RZ (suffix -2RSL or -2RZ): a non-contact elastomer lip that runs near the open 10000 r/min limiting speed, closer to the open bearing's 20000 r/min reference than the contact-seal version. It keeps coarse debris out without the drag of a contact seal, but is not liquid-tight — use 2RSH for wet or fine-dust positions.
- The 14/10.8 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61909-RSR bearing?
A 61909-RSR deep-groove ball bearing has a 45 mm bore, 68 mm outer diameter and 12 mm width (1.772 × 2.677 × 0.472 in), per ISO 15 boundary dimensions. It is fitted with two low-friction non-contact rubber seals.
What internal clearance does 61909-RSR have?
Unless a clearance suffix says otherwise, 61909-RSR is manufactured to normal (CN) radial internal clearance. Tight fits and hot shafts consume clearance in service — for those conditions order the C3 execution of 61909 and verify the residual clearance after mounting.
How should 61909-RSR be mounted?
Apply the mounting force to the ring being fitted: on a 45 mm shaft seat the press load must pass through the inner-ring face only. A fitting sleeve and an arbor press are normally sufficient at this size. Never strike the outer ring, the cage or the seals.
What lubrication does 61909-RSR need?
61909-RSR is supplied pre-greased for life and is not designed to be opened for relubrication; where a relubrication path is required, specify the open 61909 with a housing grease fitting instead.
What is the SKF designation and catalogue data for 61909-RSR?
In the SKF Rolling Bearings catalogue this size is listed as 61909-2RZ — two low-friction non-contact elastomer seals, 45×68×12 mm per ISO 15. Quoted values: C 14 kN, C0 10.8 kN, Pu 0.465 kN, limiting speed 10000 r/min, mass 140 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61909-RSR.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.