61916 bearing: complete specifications & equivalents
The 61916 is a ISO 15 radial bearing sized 80 x 110 x 16 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 80 mm |
| Outer diameter D | 110 mm |
| Width B | 16 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 25.1 kN |
| Basic static load rating C0 | 20.4 kN |
| Fatigue load limit Pu | 1.02 kN |
| Reference speed (thermal) | 12000 rpm |
| Limiting speed (mechanical) | 7500 rpm |
| Operating temperature | -40 to +150 °C |
| Mass | 380 g |
| Manufacturer designation | SKF 61916 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 4.331 in |
| Width B | 0.63 in |
| ISO bore code | 16 |
| Radial section height (D−d)/2 | 15 mm |
| Smallest bore in 61900-series | 10 mm |
| Largest outer diameter in 61900-series | 420 mm |
| Width range across 61900-series | 6–56 mm |
| Bore position in 61900-series (smallest first) | 17 of 35 |
| Bore above smallest 61900-series size | 70 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 61916-ZZ | GENERIC-ISO | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 80×110×16 mm envelope per ISO 15; seal variant differs (OPEN vs ZZ) — confirm sealing suits the duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 61916 model number is decoded
In the 61900-series (ISO 15 diameter series 9) the last two digits encode the bore: 61916 carries bore code 16 = 80 mm. Outside diameter 110 mm and width 16 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 80 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude.
Typical equipment & failure modes
Common applications
- robotics and automation joints
- lay shafts and idler shafts
- textile machinery
- packaging machinery
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- electrical pitting in VFD-driven motors without grounding protection
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 619xx thin section (15.0 mm section height at 80 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
- The open 61916 has no lubricant retention: grease escapes and contaminants migrate straight into the 80×110×16 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Open bearings tolerate the highest speeds in the 61900-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 61916 units.
- Do not quieten a noisy bearing by preloading it: the 61900-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
- The open 61916 needs external sealing and application-supplied lubrication; in the SKF catalogue the protected variants are separate order numbers 61916-2Z (shields) and 61916-2RSH (contact seals), not suffix-free 61916.
- The 25.1/20.4 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 61916 bearing?
A 61916 deep-groove ball bearing has a 80 mm bore, 110 mm outer diameter and 16 mm width (3.15 × 4.331 × 0.63 in), per ISO 15 boundary dimensions. It is an open bearing with no seals or shields.
How does the 61916 bore code work?
The last two digits of 61916 are bore code 16, giving 16 × 5 = 80 mm bore. The 110 mm outside diameter and 16 mm width follow the ISO 15 diameter series, not the bore code alone.
What does no suffix on 61916 mean?
A bare 61916 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication.
How does the 61900 compare with other series at the same 80 mm bore?
619 is a thin section one step above 618: 110×16 mm with a 15.0 mm radial section at 80 mm bore; a 6216 on the same bore is substantially larger and more heavily rated.
What is the SKF designation and catalogue data for 61916?
In the SKF Rolling Bearings catalogue this size is listed as 61916 — the open (unsealed) execution, 80×110×16 mm per ISO 15. Quoted values: C 25.1 kN, C0 20.4 kN, Pu 1.02 kN, limiting speed 7500 r/min, mass 380 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 61916.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.