61918-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61918-RSR-NTN model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61918 carries bore code 18 = 90 mm. Outside diameter 125 mm and width 18 mm come from the ISO 15 boundary-dimensions general plan. Suffix -RSR denotes two low-friction non-contact elastomer seals; they keep coarse debris out with minimal drag but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 90 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6918LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 90 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 619xx thin section (17.5 mm section height at 90 mm bore) trades load capacity for compactness; stiff, accurately aligned seats are essential or edge loading will spall the raceway early.
• The low-drag lip of 61918-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• The non-contact lip of 61918-RSR-NTN does not retain a lifetime grease fill the way a contact seal does; confirm the regreasing interval for the 90 mm bore position before relying on it as sealed-for-life.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• Do not quieten a noisy bearing by preloading it: the 61900-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• NTN catalogues this low-friction non-contact seal as 6918LLB (suffix LB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• At 90 mm bore 61918 is in NTN's medium industrial range; the pressed-steel cage is standard but large-section 63xx/64xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• At 5100 r/min the grease limiting speed for 61918 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• NTN rates 61918 at 36.5 kN dynamic (C) and 31.5 kN static (C0), 2.05 kN fatigue load limit Cu; this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 554 g, 61918 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 90×125×18 mm envelope of 61918 gives a D/d ratio of 1.39 and only 17.5 mm radial section height — this is an ultra-thin section where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 36.5/31.5 kN load ratings, 2.05 kN fatigue load limit Cu NTN lists the grease limiting speed at 5100 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 554 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6918LLB on the 90×125×18 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61918 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• Standard catalogue stock of 61918 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.