61932-2RS bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 61932-2RS model number is decoded

In the 61900-series (diameter series 9 of ISO 15) the last two digits encode the bore: 61932 carries bore code 32 = 160 mm. Outside diameter 220 mm and width 28 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 160 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK's contact-seal catalogue number is 6932DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 160 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 619xx thin section at 160 mm bore (30.0 mm section height) cannot shrug off the misalignment a standard section tolerates; keep the housing bores round and aligned, or edge contact will spall the raceways early.
• Contact seals add drag and heat: 61932-2RS runs slower and cooler-limited than the open 61932; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Never wash a sealed 61932-2RS in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Grease compatibility is not guaranteed between fills: mixing lithium and polyurea thickeners in a 61900-series position can soften the mixture and leak — clean out the old fill before switching grease types.
• Measure the shaft, do not trust the drawing: a 160 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 61932-2RS.
• NSK catalogues the contact-sealed version as 6932DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. NSK's DDU lip design is single-lip contact, so grease life is longer than VV but drag torque is higher.
• The 160 mm bore places 61932 at the lower end of NSK's large-size range; at these diameters the pressed-steel cage is speed-limited and NSK commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NSK distributor, and do not extrapolate small-bore speed ratings to this size.
• At 95.5 kN dynamic load rating (C) and 96 kN static (C0), 61932 is a heavy-load NSK bearing for industrial gearboxes and large conveyors; NSK expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 2710 g (2.7 kg), 61932 needs mechanical handling for mounting; NSK recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 160×220×28 mm envelope of 61932 gives a D/d ratio of 1.38 and only 30.0 mm radial section height — this is an ultra-thin section in NSK's E1103 catalogue where shaft deflection and housing ovality directly load the ball-raceway contact; verify shaft stiffness (target deflection under 0.05 mm) before specifying it over a 62-series.
• The 95.5/96 kN load ratings, mass 2710 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6932DDU on the 160×220×28 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 61932 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 61932 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.