W619-3-ZZ bearing: complete specifications & equivalents
The W619-3-ZZ is a ISO 15 radial bearing sized 3 x 8 x 3 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 3 mm |
| Outer diameter D | 8 mm |
| Width B | 3 mm |
| Material | SS440C |
| Seal / shield | ZZ |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 0.225 kN |
| Basic static load rating C0 | 0.072 kN |
| Fatigue load limit Pu | 0.003 kN |
| Reference speed (thermal) | 150000 rpm |
| Limiting speed (mechanical) | 75000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 0.61 g |
| Manufacturer designation | W 619/3-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 0.118 in |
|---|---|
| Outer diameter D | 0.315 in |
| Width B | 0.118 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 2.5 mm |
| Smallest bore in 61900-series | 3 mm |
| Largest outer diameter in 61900-series | 1120 mm |
| Width range across 61900-series | 3–118 mm |
| Bore position in 61900-series (smallest first) | 1 of 63 |
| Bore above smallest 61900-series size | 0 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the W619-3-ZZ model number is decoded
The W prefix denotes SKF stainless steel deep-groove bearings (X108CrMo17 / AISI 440C class rings). In the 61900-series, the bore is written directly after the slash as 3 mm (bores below 10 mm use the slash spelling). Envelope 3×8×3 mm (0.118×0.315×0.118 in), C 0.225 kN, C0 0.072 kN, Pu 0.003 kN; limiting speed 75000 r/min and mass 0.61 g. SKF spells the double shield W 619/3-2Z (suffix 2Z); the shields are non-contact, retain grease and block coarse debris but are not liquid-tight. Stainless is chosen for corrosion and washdown duty, not for extra load — the same-envelope chrome-steel bearing rates higher.
Typical equipment & failure modes
Common applications
- medical and laboratory devices
- small pumps handling corrosive media
- bicycle and outdoor equipment
- appliances exposed to moisture
Known failure patterns
- seal and grease failure before the rings corrode in sustained washdown service
- surface staining and pitting when even the stainless steel is left unlubricated in salty or acidic duty
- fine-particle abrasion when non-contact shields let dust through in a dirty environment
- grease aging inside the shielded cavity with no relubrication path
Selection pitfalls — read before you substitute
- Food, pharmaceutical and washdown positions need food-grade grease (e.g. NSF H1 registered) inside W619-3-ZZ; standard fill is industrial grease unless specified otherwise.
- Corrosion resistance depends on clean, undamaged surfaces: never weld near W619-3-ZZ or scratch the raceways during mounting, since the damaged spot starts corrosion.
- Temperatures above roughly 300 °C temper the stainless races; even standard greases fail far earlier — keep W619-3-ZZ inside the quoted grease temperature range.
- W-prefix stainless rings (X108CrMo17 / AISI 440C class) resist moisture and weak chemicals but will still rust in chloride-rich or salt-spray duty without protection — W619-3-ZZ is not marine-grade stainless.
- Do not preload W619-3-ZZ to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
- Deep-groove geometry tolerates only minutes of misalignment; if the 8 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming W619-3-ZZ.
Frequently asked questions
What are the dimensions of the stainless W619-3-ZZ?
SKF W 619/3-2Z measures 3×8×3 mm (0.118×0.315×0.118 in), about 0.61 g, C 0.225 kN.
What does the W in W 619/3-2Z mean?
W is the SKF prefix for stainless steel deep-groove bearings (rings in X108CrMo17 / AISI 440C class); the rest of the designation follows the normal series and bore rules.
Are W stainless bearings waterproof?
No — the stainless rings resist moisture and weak chemicals far better than 52100 chrome steel, but salt spray, strong chlorides and unlubricated washdown duty can still corrode W619-3-ZZ; add seals and food-grade grease for wet positions.
Can I replace a chrome-steel bearing with stainless W619-3-ZZ?
The envelope matches, but stainless rates lower (C 0.225 kN for W 619/3-2Z); for corrosive environments that trade-off is intended, for high loads it shortens life.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.