W619-9-ZZ bearing: complete specifications & equivalents
The W619-9-ZZ is a ISO 15 radial bearing sized 9 x 20 x 6 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 9 mm |
| Outer diameter D | 20 mm |
| Width B | 6 mm |
| Material | SS440C |
| Seal / shield | ZZ |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1.95 kN |
| Basic static load rating C0 | 0.93 kN |
| Fatigue load limit Pu | 0.045 kN |
| Reference speed (thermal) | 80000 rpm |
| Limiting speed (mechanical) | 40000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 7.65 g |
| Manufacturer designation | W 619/9-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 61900-series range
| Bore d | 0.354 in |
|---|---|
| Outer diameter D | 0.787 in |
| Width B | 0.236 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 5.5 mm |
| Smallest bore in 61900-series | 3 mm |
| Largest outer diameter in 61900-series | 1120 mm |
| Width range across 61900-series | 3–118 mm |
| Bore position in 61900-series (smallest first) | 7 of 63 |
| Bore above smallest 61900-series size | 6 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 619-9-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 9×20×6 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (1.95/0.93 kN vs 2.34/0.98 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| 619-9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 9×20×6 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (1.95/0.93 kN vs 2.34/0.98 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| W619-9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 9×20×6 mm envelope and equivalent catalogue ratings; W 619/9 is the open arrangement execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the W619-9-ZZ model number is decoded
The W prefix denotes SKF stainless steel deep-groove bearings (X108CrMo17 / AISI 440C class rings). In the 61900-series, the bore is written directly after the slash as 9 mm (bores below 10 mm use the slash spelling). Envelope 9×20×6 mm (0.354×0.787×0.236 in), C 1.95 kN, C0 0.93 kN, Pu 0.045 kN; limiting speed 40000 r/min and mass 7.65 g. SKF spells the double shield W 619/9-2Z (suffix 2Z); the shields are non-contact, retain grease and block coarse debris but are not liquid-tight. Stainless is chosen for corrosion and washdown duty, not for extra load — the same-envelope chrome-steel bearing rates higher.
Typical equipment & failure modes
Common applications
- washdown-duty equipment
- chemical and marine atmospheres
- medical and laboratory devices
- small pumps handling corrosive media
Known failure patterns
- seal and grease failure before the rings corrode in sustained washdown service
- surface staining and pitting when even the stainless steel is left unlubricated in salty or acidic duty
- fine-particle abrasion when non-contact shields let dust through in a dirty environment
- grease aging inside the shielded cavity with no relubrication path
Selection pitfalls — read before you substitute
- Temperatures above roughly 300 °C temper the stainless races; even standard greases fail far earlier — keep W619-9-ZZ inside the quoted grease temperature range.
- W-prefix stainless rings (X108CrMo17 / AISI 440C class) resist moisture and weak chemicals but will still rust in chloride-rich or salt-spray duty without protection — W619-9-ZZ is not marine-grade stainless.
- The stainless steel is martensitic and MAGNETIC; do not reject W619-9-ZZ over magnetism — only austenitic grades are non-magnetic, and those are too soft for bearing raceways.
- Stainless bearings carry lower load ratings than chrome steel of the same envelope: W619-9-ZZ is quoted at C 1.95 kN versus the 6 mm-wide 52100 version — do not swap on dimensions alone.
- Assign interference to the rotating ring: on a conventional shaft-mounted 9 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
- Fillet radii must clear the W619-9-ZZ chamfer so the 6 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
Frequently asked questions
What are the dimensions of the stainless W619-9-ZZ?
SKF W 619/9-2Z measures 9×20×6 mm (0.354×0.787×0.236 in), about 7.65 g, C 1.95 kN.
What does the W in W 619/9-2Z mean?
W is the SKF prefix for stainless steel deep-groove bearings (rings in X108CrMo17 / AISI 440C class); the rest of the designation follows the normal series and bore rules.
Is the stainless bearing magnetic?
Yes. Bearing stainless steels are martensitic (hardened) and magnetic; non-magnetic austenitic grades cannot be hardened enough for raceways and balls.
Where is W619-9-ZZ typically used?
Food and packaging machines, pharmaceutical equipment, washdown conveyors, chemical and marine-atmosphere drives and appliances exposed to moisture.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.