6201-2RS-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6201-2RS-NSK model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6201 carries bore code 12 = 12 mm. Outside diameter 32 mm and width 10 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 12 mm shaft, typical catalogue practice is a j5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NSK's contact-seal catalogue number is 6201DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 12 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6201 with C3 clearance and re-check the residual value after mounting.
• At 12 mm bore the 62xx light series is the workhorse section; its 32×10 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• Contact seals add drag and heat: 6201-2RS-NSK runs slower and cooler-limited than the open 6201; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Heat is the enemy of the sealed 6201-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6201-2RS-NSK-C3. No clearance suffix means normal CN clearance.
• Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• NSK catalogues the contact-sealed version as 6201DDU (suffix DDU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. NSK's DDU lip design is single-lip contact, so grease life is longer than VV but drag torque is higher.
• At 12 mm bore the 6201 sits in NSK's small-bore range; NSK ships these sizes with a pressed-steel cage and P0 tolerance as standard, and NSK's EA (extra-precision) or P5 class is a special-order upgrade for spindle duty — do not assume catalogue P0 figures hold for instrument use without an NSK engineering check.
• NSK rates 6201 at 7.5 kN dynamic (C) and 3.05 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — for conveying or gearbox duty with shock loads, verify the equivalent dynamic load stays well below C.
• At only 37 g, 6201 is a lightweight NSK bearing that can be handled by hand; still, press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 12×32×10 mm envelope of 6201 gives a D/d ratio of 2.67 and 10.0 mm radial section height — a heavy NSK section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 7.5/3.05 kN load ratings, mass 37 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6201DDU on the 12×32×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6201 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 6201 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.