6201-2RS-FAG bearing: complete specifications & equivalents

Specification table

Source: catalog reference (HR 1 Rolling Bearings (Jan 2020)) · extracted 2026-09-25

Parameters extracted from the official FAG Rolling Bearings catalogue (HR 1 Rolling Bearings (Jan 2020)); FAG® is a trademark of Schaeffler Technologies AG & Co. KG, used here for identification only — mpnbase is not an authorized FAG/Schaeffler distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at schaeffler.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6201-2RS-FAG model number is decoded

6201-2RS is closed by two contacting elastomer lips over a lifetime grease fill; the lips add friction, so the speed ceiling sits below the open execution. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 12 by five gives the 12 mm bore; the 32 mm outside diameter and 10 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 12 mm shaft under normal load, catalogue practice seats it on a j5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. Schaeffler HR 1 catalogues the lip-contact sealed version as 6201-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Temperature rise and interference fits consume internal clearance on this 12 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6201 with C3 for those conditions.
• The 62xx light series is the default general-purpose section at 12 mm bore; before upgrading to a 6312 for extra capacity, confirm the housing accepts a 32 mm OD and 10 mm width — it is not a drop-in swap.
• Contact seals add drag and heat: 6201-2RS-FAG runs slower and cooler-limited than the open 6201; rubber lips are generally limited to roughly 80–110 °C continuous depending on grease, and C3 clearance is the common hot-duty choice.
• Never wash a sealed 6201-2RS-FAG in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 10 mm-wide ring of 6201-2RS-FAG drags the lip and overheats it.
• Vibration during standstill brinells the raceways of a 12 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• Schaeffler HR 1 lists the lip-contact sealed version as 6201-C-2HRS (FAG suffix 2RSR), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing. FAG's RSR lip material is NBR as standard — above roughly 100 °C continuous, consult Schaeffler for higher-temperature seal options.
• FAG rates 6201 at 22500 r/min mechanical limiting speed — a high-speed range where the thermal reference speed governs continuous duty; use low-viscosity turbine oil or high-speed grease and avoid lip-contact seals entirely.
• At 12 mm bore the 6201 sits in Schaeffler's small-bore range; HR 1 ships these sizes with a pressed steel or plastic cage and P0 tolerance as standard — for instrument or spindle accuracy order the P6/P5 variant explicitly, since P0 runout figures will not hold.
• FAG rates 6201 at 8 kN dynamic (C) and 3.1 kN static (C0); this light-to-medium rating suits fractional-horsepower drives and instruments — verify the equivalent dynamic load stays well below C for conveying or gearbox duty with shock.
• At only 36 g, 6201 is a lightweight FAG bearing that can be handled by hand; still press it onto the shaft with a sleeve against the inner ring — never through the balls or outer ring.
• The 12×32×10 mm envelope of 6201 gives a D/d ratio of 2.67 and 10.0 mm radial section height — a heavy FAG section for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 8/3.1 kN load ratings, mass 36 g here are Schaeffler HR 1 Rolling Bearings (Jan 2020) catalogue figures for 6201-C-2HRS on the 12×32×10 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6201 in a rated drive. Where FAG has since released an X-life version of this size, its expanded C/C0 ratings supersede the HR 1 print values quoted here.
• Schaeffler has moved many HR 1 sizes to the X-life generation with higher C/C0 ratings; the designation is unchanged, so a current eKatalog listing for 6201 may quote higher values than the HR 1 print figures on this page — the envelope is identical either way.
• Mixing old and new FAG generations of the same designation in one arrangement is dimensionally acceptable, but where ratings matter — preloaded or matched sets — order both positions from the same generation and lot.