6209-RSR-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6209-RSR-NTN model number is decoded

6209-RSR uses two non-contact elastomer lips with very low drag; coarse debris stays out, but the bearing is not liquid-tight. Within the light 62xx section (diameter series 2 of ISO 15), multiplying bore code 09 by five gives the 45 mm bore; the 85 mm outside diameter and 19 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 45 mm shaft under normal load, catalogue practice seats it on a k5 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NTN's non-contact seal suffix is LLB/LLF (catalogue number 6209LLB), mapped here from the industry-neutral -RSR spelling; speed capability matches the open bearing but it is not liquid-tight.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At a 45 mm bore, a shaft-seat burr or an overtight setscrew can score the thin inner ring of 6209-RSR-NTN; check shaft finish and runout (target Ra ≤ 1.6 µm) before pressing it home.
• The 62xx light series is the default general-purpose section at 45 mm bore; before upgrading to a 6309 for extra capacity, confirm the housing accepts a 85 mm OD and 19 mm width — it is not a drop-in swap.
• RSR low-friction seals on 6209-RSR-NTN run faster than contact-seal 6209-2RS but let fine dust and moisture past the non-contact lip; in dirty or wet duty specify 6209-2RS instead.
• The low-drag lip of 6209-RSR-NTN barely touches the inner ring; after long shelf storage the grease can separate, so rotate the rings by hand and confirm smooth, silent running before fitting.
• Measure the shaft, do not trust the drawing: a 45 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6209-RSR-NTN.
• Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• NTN catalogues this low-friction non-contact seal as 6209LLB (suffix LLB), mapped here from the industry-neutral -RSR spelling. NTN rates its speed capability the same as the open bearing, but it is not liquid-tight — for wet or fine-dust duty step up to the LLU contact seal (industry-neutral -2RS).
• The 45 mm bore puts 6209 in NTN's general-purpose industrial range; the standard pressed-steel cage and CN clearance cover most electric-motor and pump duty, but for continuous high-speed use specify the LLH low-torque seal (not LLU) and confirm the housing allows the listed limiting speed.
• At 6200 r/min the grease limiting speed for 6209 covers medium-duty industrial drives; the open or shielded execution can run continuously at this speed with standard lithium-soap grease.
• NTN rates 6209 at 36 kN dynamic (C) and 20.4 kN static (C0), 1.6 kN fatigue load limit Cu; this upper-medium rating covers conveyor and gearbox drives, but at these loads the pressed-steel cage can be the limiting factor under shock — consider the machined brass cage (suffix M) for impact duty.
• At 398 g, 6209 requires a soft-jaw vise or arbor press for mounting — never hammer it onto the shaft, and support the opposite ring to avoid brinelling the raceways.
• The 45×85×19 mm envelope of 6209 gives a D/d ratio of 1.89 and 20.0 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 36/20.4 kN load ratings, 1.6 kN fatigue load limit Cu NTN lists the grease limiting speed at 6200 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 398 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6209LLB on the 45×85×19 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6209 in a rated drive.
• Two NTN bearings of the same designation from different production lots can carry minor internal-geometry revisions; for paired or preloaded arrangements on one shaft, order a single lot through the NTN distributor.
• Order the C3 internal-clearance version (6209 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.