6210-ZZ bearing: complete specifications & equivalents
The 6210-ZZ is a ISO 15 radial bearing sized 50 x 90 x 20 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Bore diameter d | 50 mm |
| Outer diameter D | 90 mm |
| Width B | 20 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 37.1 kN |
| Basic static load rating C0 | 23.2 kN |
| Fatigue load limit Pu | 0.98 kN |
| Reference speed (thermal) | 15000 rpm |
| Limiting speed (mechanical) | 8000 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 470 g |
| Manufacturer designation | SKF 6210-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-24 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 1.969 in |
|---|---|
| Outer diameter D | 3.543 in |
| Width B | 0.787 in |
| ISO bore code | 10 |
| Radial section height (D−d)/2 | 20 mm |
| Smallest bore in 6200-series | 10 mm |
| Largest outer diameter in 6200-series | 400 mm |
| Width range across 6200-series | 9–65 mm |
| Bore position in 6200-series (smallest first) | 11 of 33 |
| Bore above smallest 6200-series size | 40 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6210 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range. Brand-specific OEM equivalents pending multi-source data. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6210-ZZ model number is decoded
In the 6200-series (ISO 15 diameter series 2) the last two digits encode the bore: 6210 carries bore code 10 = 50 mm. Outside diameter 90 mm and width 20 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 50 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. SKF's own suffix is 2Z (this page's industry-neutral spelling is -ZZ); catalogue number 6210-2Z.
Typical equipment & failure modes
Common applications
- industrial electric motors
- centrifugal and positive-displacement pumps
- gearboxes and speed reducers
- conveyor drives
Known failure patterns
- fine-particle abrasion when non-contact shields let dust past in dirty duty
- grease aging in the shield-for-life cavity with no relubrication path
- raceway smearing under marginal lubrication at start-up
- edge loading from shaft deflection or housing misalignment
Selection pitfalls — read before you substitute
- Temperature rise and interference fits consume internal clearance on this 50 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6210 with C3 for those conditions.
- The 62xx light series is the default general-purpose section at 50 mm bore; before upgrading to a 6310 for extra capacity, confirm the housing accepts a 90 mm OD and 20 mm width — it is not a drop-in swap.
- ZZ shields are non-contact: 6210-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6210-2RS for that.
- Shielded 6210-ZZ units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
- Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
- SKF spells the shielded version 6210-2Z (one shield: 6210-Z), not "-ZZ": the suffix language differs by brand even though the ISO envelope is identical, so quote the brand designation when ordering.
- The single-shield execution 6210-Z is a distinct order number in catalogue 17000: it suits open gears or oil-bath arrangements where the unshielded face faces the lubricant, and it is not interchangeable with the double-shield 6210-2Z for high-contamination positions.
- The 37.1/23.2 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6210-ZZ bearing?
A 6210-ZZ deep-groove ball bearing has a 50 mm bore, 90 mm outer diameter and 20 mm width (1.969 × 3.543 × 0.787 in), per ISO 15 boundary dimensions. It is fitted with two non-contact metallic shields. Geometry-based estimated mass is about 449 g for a steel-cage unit; catalogue masses vary slightly with seal and cage design.
How does the 6210 bore code work?
The last two digits of 6210 are bore code 10, giving 10 × 5 = 50 mm bore. The 90 mm outside diameter and 20 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the ZZ suffix on 6210-ZZ mean?
ZZ means two non-contact sheet-metal shields, one each side. They retain factory grease and block coarse particles with little friction, but do not seal against liquids, fine dust or pressure washing.
How does the 6200 compare with other series at the same 50 mm bore?
The '2' is the light diameter series: 90×20 mm with a 20.0 mm radial section at 50 mm bore. A 6310 on the same bore is larger and higher-rated; a 6010 is smaller and lower-rated.
What is the SKF designation and catalogue data for 6210-ZZ?
In the SKF Rolling Bearings catalogue this size is listed as 6210-2Z — two non-contact sheet-metal shields, 50×90×20 mm per ISO 15. Quoted values: C 37.1 kN, C0 23.2 kN, Pu 0.98 kN, limiting speed 8000 r/min, mass 470 g. Brand suffixes (2Z, 2RSH) differ from the industry-neutral spelling 6210-ZZ.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-24. Read our editorial & correction policy.