6214-ZZ bearing: complete specifications & equivalents
The 6214-ZZ is a ISO 15 radial bearing sized 70 x 125 x 24 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 70 mm |
| Outer diameter D | 125 mm |
| Width B | 24 mm |
| Material | GCr15 |
| Seal / shield | ZZ |
| Internal clearance | CN / C3 available |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 63.7 kN |
| Basic static load rating C0 | 45 kN |
| Fatigue load limit Pu | 1.9 kN |
| Reference speed (thermal) | 11000 rpm |
| Limiting speed (mechanical) | 5600 rpm |
| Operating temperature | -30 to +120 °C |
| Mass | 1150 g |
| Manufacturer designation | SKF 6214-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-25 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-24
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 2.756 in |
|---|---|
| Outer diameter D | 4.921 in |
| Width B | 0.945 in |
| ISO bore code | 14 |
| Radial section height (D−d)/2 | 27.5 mm |
| Smallest bore in 6200-series | 3 mm |
| Largest outer diameter in 6200-series | 540 mm |
| Width range across 6200-series | 2.5–85 mm |
| Bore position in 6200-series (smallest first) | 23 of 45 |
| Bore above smallest 6200-series size | 67 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 6214 | ISO 15 | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | ISO 15 boundary-dimension envelope; seal suffix convention varies by brand (2RS / DDU / LLU / 2RSR) — verify seal design and temperature range before substituting. |
| 6214-2RS-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 70×125×24 mm envelope per ISO 15; seal variant differs (ZZ vs 2RS) — confirm sealing suits the duty. |
| 6214-NSK | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 70×125×24 mm envelope per ISO 15; seal variant differs (ZZ vs OPEN) — confirm sealing suits the duty. |
| 6214-RSR | NSK | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 70×125×24 mm envelope per ISO 15; seal variant differs (ZZ vs RSR) — confirm sealing suits the duty. |
| 6214-ZZ-NSK | NSK | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 6214-2RS-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 70×125×24 mm envelope per ISO 15; seal variant differs (ZZ vs 2RS) — confirm sealing suits the duty. |
| 6214-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 70×125×24 mm envelope per ISO 15; seal variant differs (ZZ vs OPEN) — confirm sealing suits the duty. |
| 6214-RSR-NTN | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 70×125×24 mm envelope per ISO 15; seal variant differs (ZZ vs RSR) — confirm sealing suits the duty. |
| 6214-ZZ-NTN | NTN | full Dimensions and internal design equivalent — standard interchange. | Identical ISO 15 envelope, seal and ratings band — standard interchange; re-verify precision class and clearance per supplier. |
| 7214 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| NU214 | SKF | verify Commonly quoted cross reference; confirm against the target catalog before ordering. | — |
| 6214-M | SKF | full Dimensions and internal design equivalent — standard interchange. | SKF 6214 M (machined brass cage, open arrangement) is the same-size execution on the 70×125×24 mm envelope with ratings within 10 % — boundary dimensions interchangeable. |
| 214 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 214 shares the 70×125×24 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
| 214-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | SKF 214-2Z shares the 70×125×24 mm envelope but catalogue C/C0 differ — envelope match only after a load check. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 6214-ZZ model number is decoded
In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6214 carries bore code 14 = 70 mm. Outside diameter 125 mm and width 24 mm come from the ISO 15 boundary-dimensions general plan. Suffix -ZZ denotes two non-contact metallic shields; they retain grease and block coarse debris but are not liquid-tight. For normal-load mounting with a rotating inner ring on a 70 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. SKF's own suffix is 2Z (this page's industry-neutral spelling is -ZZ); catalogue number 6214-2Z.
Typical equipment & failure modes
Common applications
- industrial fans
- industrial electric motors
- centrifugal and positive-displacement pumps
- gearboxes and speed reducers
Known failure patterns
- fine-particle abrasion when non-contact shields let dust past in dirty duty
- grease aging in the shield-for-life cavity with no relubrication path
- electrical pitting in VFD-driven motors without grounding protection
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Temperature rise and interference fits consume internal clearance on this 70 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 6214 with C3 for those conditions.
- At 70 mm bore the 62xx light series is the workhorse section; its 125×24 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
- ZZ shields are non-contact: 6214-ZZ blocks chips and coarse dust but is not waterproof — do not install it expecting a pressure-wash seal, step up to 6214-2RS for that.
- Do not wash 6214-ZZ in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
- Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
- Shaft and housing fillets must clear the bearing chamfer so the 24 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
- SKF spells the shielded version 6214-2Z (one shield: 6214-Z), not "-ZZ": the suffix language differs by brand even though the ISO envelope is identical, so quote the brand designation when ordering.
- The single-shield execution 6214-Z is a distinct order number in catalogue 17000: it suits open gears or oil-bath arrangements where the unshielded face faces the lubricant, and it is not interchangeable with the double-shield 6214-2Z for high-contamination positions.
- The 63.7/45 kN ratings here are SKF Explorer-class figures from catalogue PUB BU/P1 17000/1 EN (Oct 2018); SKF can revise internal geometry and ratings without changing the designation, so treat the catalogue version and date as part of the specification and re-verify for critical drives.
Frequently asked questions
What are the dimensions of a 6214-ZZ bearing?
A 6214-ZZ deep-groove ball bearing has a 70 mm bore, 125 mm outer diameter and 24 mm width (2.756 × 4.921 × 0.945 in), per ISO 15 boundary dimensions. It is fitted with two non-contact metallic shields.
What internal clearance does 6214-ZZ have?
Unless a clearance suffix says otherwise, 6214-ZZ is manufactured to normal (CN) radial internal clearance. Tight fits and hot shafts consume clearance in service — for those conditions order the C3 execution of 6214 and verify the residual clearance after mounting.
How should 6214-ZZ be mounted?
Apply the mounting force to the ring being fitted: on a 70 mm shaft seat the press load must pass through the inner-ring face only. Induction heating of the inner ring (max 120 °C) is the clean method at this size. Never strike the outer ring, the cage or the seals.
What lubrication does 6214-ZZ need?
6214-ZZ is greased at the factory and the shields hold the fill for the bearing's service life; relubrication is not intended, and adding grease through the shield gap usually forces dirt in with it.
What is the SKF designation and catalogue data for 6214-ZZ?
In the SKF Rolling Bearings catalogue this size is listed as 6214-2Z — two non-contact sheet-metal shields, 70×125×24 mm per ISO 15. Quoted values: C 63.7 kN, C0 45 kN, Pu 1.9 kN, limiting speed 5600 r/min, mass 1150 g. Brand suffixes (2Z, 2RSH, 2RSL) differ from the industry-neutral spelling 6214-ZZ.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-25. Read our editorial & correction policy.