6230-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6230-NSK model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6230 carries bore code 30 = 150 mm. Outside diameter 270 mm and width 45 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 150 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 150 mm of 6230-NSK demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• The 62xx light series is the default general-purpose section at 150 mm bore; before upgrading to a 6330 for extra capacity, confirm the housing accepts a 270 mm OD and 45 mm width — it is not a drop-in swap.
• The open 6230-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 150×270×45 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6230 units.
• Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• Measure the shaft, do not trust the drawing: a 150 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6230-NSK.
• The open 6230 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 150 mm bore places 6230 at the lower end of NSK's large-size range; at these diameters the pressed-steel cage is speed-limited and NSK commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NSK distributor, and do not extrapolate small-bore speed ratings to this size.
• NSK rates 6230 at 194 kN dynamic (C) and 168 kN static (C0); this heavy-load rating is at the upper end of the E1103 Part C single-row deep-groove extract — NSK supplies a machined brass cage (suffix M) and expects an application review, because catalogue L10 life alone does not capture shock and misalignment loads at this rating.
• At 10000 g (10.0 kg), 6230 is a heavy NSK bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 150×270×45 mm envelope of 6230 gives a D/d ratio of 1.80 and 60.0 mm radial section height — a standard NSK medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to NSK's listed speed ratings, and C3 clearance is the common choice for hot shafts.
• The 194/168 kN load ratings, mass 10000 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6230 on the 150×270×45 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6230 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 6230 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.