6248 bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6248 model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6248 carries bore code 48 = 240 mm. Outside diameter 440 mm and width 72 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 240 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 240 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 62xx light series is the default general-purpose section at 240 mm bore; before upgrading to a 6348 for extra capacity, confirm the housing accepts a 440 mm OD and 72 mm width — it is not a drop-in swap.
• Storage matters for open bearings: 6248 leaves the factory with rust preventive only, so clean it and apply the service grease at assembly even if the rings look oily from the wrapper.
• Open bearings tolerate the highest speeds in the 6200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6248 units.
• A 240 mm bore listing showing the right d/D/B but no standard or precision-class reference may be a loose-tolerance import; measure bore/OD spread before fitting it to a machined shaft.
• Do not quieten a noisy bearing by preloading it: the 6200-series is a deep-groove design, not angular-contact; axial preload raises temperature and shortens grease life.
• The open 6248 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• The 240 mm bore places 6248 at the upper end of NSK's single-row deep-groove catalogue for the E1103 Part C extract; this is a heavy-engineering bearing where centrifugal force and cage inertia dominate the design envelope. NSK supplies a machined brass cage (suffix M) and expects oil lubrication with a defined relubrication interval — do not use catalogue grease speed figures for this size without an NSK engineering review.
• NSK rates 6248 at 375 kN dynamic (C) and 430 kN static (C0); this is an extreme-load bearing at the top of the E1103 Part C single-row deep-groove range, where mounting, shaft stiffness and housing alignment dominate the achievable life. Consult NSK engineering for a full application review rather than relying on catalogue L10 alone.
• At 50500 g (50.5 kg), 6248 is a very heavy NSK bearing where handling and mounting method directly affect service life; NSK requires induction heating of the inner ring (max 120 °C), a mechanical puller for removal, and a defined lifting procedure to avoid damaging the cage.
• The 240×440×72 mm envelope of 6248 gives a D/d ratio of 1.83 and 100.0 mm radial section height — a standard NSK medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to NSK's listed speed ratings, and C3 clearance is the common choice for hot shafts.
• The 375/430 kN load ratings, mass 50500 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6248 on the 240×440×72 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6248 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• NSK does not recommend washing new shielded or sealed bearings; the rust-preventive film on open units is compatible with standard lithium greases and needs no removal unless the application demands a special fill.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 6248 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.