6244-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6244-NTN model number is decoded

In the 6200-series (diameter series 2 of ISO 15) the last two digits encode the bore: 6244 carries bore code 44 = 220 mm. Outside diameter 400 mm and width 65 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 220 mm shaft, typical catalogue practice is a m6 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 220 mm of 6244-NTN demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• At 220 mm bore the 62xx light series is the workhorse section; its 400×65 mm envelope is what most motor and gearbox seats are machined for, so any alternative section must be checked against both this OD and this width, not the bore alone.
• The open 6244-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 220×400×65 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6200-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6244 units.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6244-NTN-C3. No clearance suffix means normal CN clearance.
• Axial location must clamp the ring face, not the seal area: a shoulder or circlip bearing on the seal side of the 65 mm-wide ring of 6244-NTN drags the lip and overheats it.
• The open 6244 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 220 mm bore places 6244 in NTN's upper large-size range; centrifugal force at this diameter sharply caps the grease limiting speed, so NTN usually supplies a machined brass cage (suffix M) and expects oil lubrication for continuous duty. Confirm relubrication interval and cage material with the NTN distributor.
• NTN lists the grease limiting speed at 1500 r/min for 6244; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• NTN rates 6244 at 330 kN dynamic (C) and 365 kN static (C0), 15.8 kN fatigue load limit Cu; this is an upper heavy-load rating where the pressed-steel cage is not recommended — NTN supplies a machined brass cage (suffix M) and the static C0 must be verified against any shock or lifting loads the bearing sees during mounting.
• At 30200 g (30.2 kg), 6244 is a very heavy bearing where handling and mounting method directly affect service life; NTN requires induction heating of the inner ring (max 120 °C), a mechanical puller for removal, and a defined lifting procedure to avoid damaging the machined brass cage.
• The 220×400×65 mm envelope of 6244 gives a D/d ratio of 1.82 and 90.0 mm radial section height — a standard medium section that balances load capacity and speed; for this geometry the pressed-steel cage is adequate up to the listed limiting speed, and C3 clearance is the common choice for hot shafts.
• The 330/365 kN load ratings, 15.8 kN fatigue load limit Cu NTN lists the grease limiting speed at 1500 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 30200 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6244 on the 220×400×65 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6244 in a rated drive.
• Standard catalogue stock of 6244 is the general-purpose execution; for low-noise motor duty NTN offers low-torque seal and special-grease variants in this size class, which are separate order numbers.
• Order the C3 internal-clearance version (6244 with C3 after the seal code) when the shaft fit is tight or the shaft-to-housing temperature gradient exceeds roughly 10 °C — the residual clearance after mounting, not the catalogue CN figure, decides service life.