6244-M (brass cage) bearing: complete specifications & equivalents

The 6244-M is a ISO 15 radial bearing sized 220 x 400 x 65 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 400 mm d = 220 B = 65 mm side section front view
Principal dimensions: bore d 220 mm, outer diameter D 400 mm, width B 65 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 220 mm
Outer diameter D 400 mm
Width B 65 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage brass
Basic dynamic load rating C 296 kN
Basic static load rating C0 365 kN
Fatigue load limit Pu 8.8 kN
Reference speed (thermal) 3200 rpm
Limiting speed (mechanical) 3000 rpm
Operating temperature -40 to +120 °C
Mass 36500 g
Manufacturer designation 6244 M
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6200-series range

Bore d8.661 in
Outer diameter D15.748 in
Width B2.559 in
ISO bore code44
Radial section height (D−d)/290 mm
Smallest bore in 6200-series3 mm
Largest outer diameter in 6200-series540 mm
Width range across 6200-series2.5–85 mm
Bore position in 6200-series (smallest first)41 of 45
Bore above smallest 6200-series size217 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
6244-NSK NSK partial
Main dimensions match; tolerances, seals or internal clearance differ.
NSK bearing NSK 6244 on the same 220×400×65 mm envelope, but catalogue C/C0 differ (296/365 kN vs 340/375 kN) — envelope interchange only after a load check.
6244-NTN NTN partial
Main dimensions match; tolerances, seals or internal clearance differ.
NTN bearing 6244 on the same 220×400×65 mm envelope, but catalogue C/C0 differ (296/365 kN vs 330/365 kN) — envelope interchange only after a load check.
6244 SKF full
Dimensions and internal design equivalent — standard interchange.
SKF SKF 6244 (open arrangement) shares the 220×400×65 mm envelope with ratings within 10 % — execution variant of the same size; boundary dimensions interchangeable.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6244-M model number is decoded

In the 6200-series, the last two digits encode the bore: 6244 carries code 44 = 220 mm (code × 5). The envelope is 220×400×65 mm (8.661×15.748×2.559 in) with a 90.0 mm radial section height, C 296 kN, C0 365 kN and Pu 8.8 kN. The open 6244 M carries no shields or seals and relies on application lubrication and external sealing. The M suffix identifies the machined brass cage execution, a separate order number from the pressed-steel version. Limiting speed 3000 r/min, catalogue mass 36500 g.

Typical equipment & failure modes

Common applications

  • mill and kiln auxiliaries
  • pulp and paper machinery
  • marine deck machinery
  • crusher auxiliary drives

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Fillet radii must clear the 6244-M chamfer so the 65 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • Do not preload 6244-M to silence it: a deep-groove ball bearing is not angular-contact, and axial preload only raises temperature and shortens grease life.
  • The M suffix on 6244-M denotes a machined brass cage: it is the choice for high speeds, marginal lubrication and shock/vibration duty, and it is temperature-tolerant where polymer cages are not — the 36500 g quoted mass includes the heavier cage.
  • Open 6244-M needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 6244-M; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • At 220 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • SKF date-codes its packaging, and greased sealed or shielded bearings carry a finite shelf life: rotate stock first-in-first-out and store boxes dry, cool and away from vibration.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.

Frequently asked questions

What are the dimensions of 6244-M?

The SKF 6244 M measures 220 mm bore × 400 mm OD × 65 mm width (8.661 × 15.748 × 2.559 in), mass about 36500 g. It is open, with no shields or seals.

How does the bore code in 6244 work?

The final two digits of 6244 are bore code 44, multiplied by 5 to give 220 mm.

What is the difference between 6244-M and a same-bore 62-series bearing?

Section height differs: 6244-M has a 90 mm radial section and C 296 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.

Which fits should I use for 6244-M?

With a rotating inner ring use roughly m6 on the shaft and H7 in the 400 mm housing; reverse the interference if the outer ring rotates.

How heavy is 6244-M?

Catalogue mass is 36500 g for 6244 M; seal and cage executions of the same envelope differ by a few grams.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.