627 bearing: complete specifications & equivalents

The 627 is a ISO 15 radial bearing sized 7 x 22 x 7 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 22 mm d = 7 B = 7 mm side section front view
Principal dimensions: bore d 7 mm, outer diameter D 22 mm, width B 7 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 7 mm
Outer diameter D 22 mm
Width B 7 mm
Material GCr15
Seal / shield open
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 3.45 kN
Basic static load rating C0 1.37 kN
Fatigue load limit Pu 0.057 kN
Reference speed (thermal) 70000 rpm
Limiting speed (mechanical) 45000 rpm
Operating temperature -40 to +120 °C
Mass 12 g
Manufacturer designation 627
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 6200-series range

Bore d0.276 in
Outer diameter D0.866 in
Width B0.276 in
ISO bore code—
Radial section height (D−d)/27.5 mm
Smallest bore in 6200-series3 mm
Largest outer diameter in 6200-series540 mm
Width range across 6200-series2.5–85 mm
Bore position in 6200-series (smallest first)5 of 45
Bore above smallest 6200-series size4 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
627-2RS SKF full
Dimensions and internal design equivalent — standard interchange.
Same 7×22×7 mm envelope and equivalent catalogue ratings; 627-2RSH is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs.
627-RSR SKF full
Dimensions and internal design equivalent — standard interchange.
Same 7×22×7 mm envelope and equivalent catalogue ratings; 627-2RSL is the low-friction non-contact seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs.
627-ZZ SKF full
Dimensions and internal design equivalent — standard interchange.
Same 7×22×7 mm envelope and equivalent catalogue ratings; 627-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs.
W627-2RS SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 7×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (3.45/1.37 kN vs 1.99/0.78 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty.
W627-ZZ SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 7×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (3.45/1.37 kN vs 1.99/0.78 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty.
W627 SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 7×22×7 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (3.45/1.37 kN vs 1.99/0.78 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 627 model number is decoded

In the 6200-series, the final digit is the bore in millimetres: 627 fits a 7 mm shaft (direct-number miniature spelling). The envelope is 7×22×7 mm (0.276×0.866×0.276 in) with a 7.5 mm radial section height, C 3.45 kN, C0 1.37 kN and Pu 0.057 kN. The open 627 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 45000 r/min, catalogue mass 12 g.

Typical equipment & failure modes

Common applications

  • domestic appliances
  • instrument and encoder drives
  • model-making and hobby mechanics
  • small pumps

Known failure patterns

  • contamination wear when the open arrangement is used without external seals
  • lubricant starvation where no regreasing interval is maintained
  • cage damage from running beyond the limiting speed
  • raceway smearing under marginal lubrication at start-up

Selection pitfalls — read before you substitute

  • At 7 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • Catalogue ratings for 627 (C 3.45 kN, C0 1.37 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • Open 627 needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
  • Plan a relubrication interval for 627; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 627-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • At 7 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • Where two 627 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.
  • SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.

Frequently asked questions

What are the dimensions of 627?

The SKF 627 measures 7 mm bore × 22 mm OD × 7 mm width (0.276 × 0.866 × 0.276 in), mass about 12 g. It is open, with no shields or seals.

How do I read the 627 designation?

Small miniature bearings print the bore as the final digit, so 627 is a 7 mm bearing; the series digits in front give the section (OD/width family).

Which fits should I use for 627?

With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 22 mm housing; reverse the interference if the outer ring rotates.

How heavy is 627?

Catalogue mass is 12 g for 627; seal and cage executions of the same envelope differ by a few grams.

What internal clearance does 627 have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.