629 bearing: complete specifications & equivalents
The 629 is a ISO 15 radial bearing sized 9 x 26 x 8 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 9 mm |
| Outer diameter D | 26 mm |
| Width B | 8 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 4.75 kN |
| Basic static load rating C0 | 1.96 kN |
| Fatigue load limit Pu | 0.083 kN |
| Reference speed (thermal) | 60000 rpm |
| Limiting speed (mechanical) | 38000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 20 g |
| Manufacturer designation | 629 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 0.354 in |
|---|---|
| Outer diameter D | 1.024 in |
| Width B | 0.315 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 8.5 mm |
| Smallest bore in 6200-series | 3 mm |
| Largest outer diameter in 6200-series | 540 mm |
| Width range across 6200-series | 2.5–85 mm |
| Bore position in 6200-series (smallest first) | 6 of 45 |
| Bore above smallest 6200-series size | 6 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 629-2RS | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 9×26×8 mm envelope and equivalent catalogue ratings; 629-2RSH is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 629-RSR | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 9×26×8 mm envelope and equivalent catalogue ratings; 629-2RSL is the low-friction non-contact seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| 629-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 9×26×8 mm envelope and equivalent catalogue ratings; 629-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| W629-2RS | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 9×26×8 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (4.75/1.96 kN vs 3.97/1.96 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
| W629-ZZ | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 9×26×8 mm envelope, but the stainless and chrome-steel executions carry different catalogue ratings (4.75/1.96 kN vs 3.97/1.96 kN) — envelope match, not a load-rating equivalent; choose by corrosion versus load duty. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 629 model number is decoded
In the 6200-series, the final digit is the bore in millimetres: 629 fits a 9 mm shaft (direct-number miniature spelling). The envelope is 9×26×8 mm (0.354×1.024×0.315 in) with a 8.5 mm radial section height, C 4.75 kN, C0 1.96 kN and Pu 0.083 kN. The open 629 carries no shields or seals and relies on application lubrication and external sealing. Limiting speed 38000 r/min, catalogue mass 20 g.
Typical equipment & failure modes
Common applications
- model-making and hobby mechanics
- small pumps
- office equipment
- fractional-horsepower motors
Known failure patterns
- contamination wear when the open arrangement is used without external seals
- lubricant starvation where no regreasing interval is maintained
- electrical pitting in VFD-driven motors without shaft grounding
- edge loading from shaft deflection or housing misalignment
Selection pitfalls — read before you substitute
- The fatigue load limit is 0.083 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- Assign interference to the rotating ring: on a conventional shaft-mounted 9 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
- Open 629 needs external sealing at the arrangement level; in dusty housings its life depends entirely on those external seals and the regreasing schedule.
- Plan a relubrication interval for 629; run-to-failure on open deep-groove bearings is the dominant early-failure cause.
- Assign interference to the rotating ring: on a conventional shaft-mounted 9 mm position the inner ring rotates, so use a k5/m6 shaft seat with an H7 housing — reverse the logic if the outer ring rotates.
- Deep-groove geometry tolerates only minutes of misalignment; if the 26 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 629.
- Where two 629 bearings share one shaft in a preloaded or matched arrangement, order both from the same production lot; catalogue figures describe a single bearing, not a matched set.
- SKF Explorer deep-groove bearings of this size are produced to tight internal-geometry control; rating revisions between catalogue years do not change the designation, so keep the catalogue edition with the machine documentation.
Frequently asked questions
What are the dimensions of 629?
The SKF 629 measures 9 mm bore × 26 mm OD × 8 mm width (0.354 × 1.024 × 0.315 in), mass about 20 g. It is open, with no shields or seals.
How do I read the 629 designation?
Small miniature bearings print the bore as the final digit, so 629 is a 9 mm bearing; the series digits in front give the section (OD/width family).
What is the speed rating of 629?
SKF lists a 60000 r/min thermal reference speed and a 38000 r/min mechanical limiting speed for 629; real limits also depend on lubrication and fits.
What is the difference between 629 and a same-bore 62-series bearing?
Section height differs: 629 has a 8.5 mm radial section and C 4.75 kN; always match d, D and B — same bore alone never makes two bearings interchangeable.
Which fits should I use for 629?
With a rotating inner ring use roughly j5/k5 on the shaft and H7 in the 26 mm housing; reverse the interference if the outer ring rotates.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.