W625 bearing: complete specifications & equivalents
The W625 is a ISO 15 radial bearing sized 5 x 16 x 5 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 5 mm |
| Outer diameter D | 16 mm |
| Width B | 5 mm |
| Material | SS440C |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 1.43 kN |
| Basic static load rating C0 | 0.63 kN |
| Fatigue load limit Pu | 0.027 kN |
| Reference speed (thermal) | 100000 rpm |
| Limiting speed (mechanical) | 63000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 4.4 g |
| Manufacturer designation | W 625 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 0.197 in |
|---|---|
| Outer diameter D | 0.63 in |
| Width B | 0.197 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 5.5 mm |
| Smallest bore in 6200-series | 3 mm |
| Largest outer diameter in 6200-series | 540 mm |
| Width range across 6200-series | 2.5–85 mm |
| Bore position in 6200-series (smallest first) | 3 of 45 |
| Bore above smallest 6200-series size | 2 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| W625-2RS | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 5×16×5 mm envelope and equivalent catalogue ratings; W 625-2RS1 is the two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
| W625-ZZ | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 5×16×5 mm envelope and equivalent catalogue ratings; W 625-2Z is the two non-contact shields execution of this size — boundary dimensions interchangeable, only the seal/shield/cage execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the W625 model number is decoded
The W prefix denotes SKF stainless steel deep-groove bearings (X108CrMo17 / AISI 440C class rings). In the 6200-series, the final digit is the bore in millimetres: 625 fits a 5 mm shaft (direct-number miniature spelling). Envelope 5×16×5 mm (0.197×0.63×0.197 in), C 1.43 kN, C0 0.63 kN, Pu 0.027 kN; limiting speed 63000 r/min and mass 4.4 g. The open W 625 carries no shields or seals and relies on application lubrication and external sealing. Stainless is chosen for corrosion and washdown duty, not for extra load — the same-envelope chrome-steel bearing rates higher.
Typical equipment & failure modes
Common applications
- bicycle and outdoor equipment
- appliances exposed to moisture
- food and beverage conveyors
- pharmaceutical and packaging machines
Known failure patterns
- seal and grease failure before the rings corrode in sustained washdown service
- surface staining and pitting when even the stainless steel is left unlubricated in salty or acidic duty
- contamination wear when the open arrangement is used without external seals
- lubricant starvation where no regreasing interval is maintained
Selection pitfalls — read before you substitute
- Food, pharmaceutical and washdown positions need food-grade grease (e.g. NSF H1 registered) inside W625; standard fill is industrial grease unless specified otherwise.
- Corrosion resistance depends on clean, undamaged surfaces: never weld near W625 or scratch the raceways during mounting, since the damaged spot starts corrosion.
- Temperatures above roughly 300 °C temper the stainless races; even standard greases fail far earlier — keep W625 inside the quoted grease temperature range.
- W-prefix stainless rings (X108CrMo17 / AISI 440C class) resist moisture and weak chemicals but will still rust in chloride-rich or salt-spray duty without protection — W625 is not marine-grade stainless.
- Clearance suffixes follow the seal code in the designation stack (e.g. W 625-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
- The fatigue load limit is 0.027 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
Frequently asked questions
What are the dimensions of the stainless W625?
SKF W 625 measures 5×16×5 mm (0.197×0.63×0.197 in), about 4.4 g, C 1.43 kN.
What does the W in W 625 mean?
W is the SKF prefix for stainless steel deep-groove bearings (rings in X108CrMo17 / AISI 440C class); the rest of the designation follows the normal series and bore rules.
Is the stainless bearing magnetic?
Yes. Bearing stainless steels are martensitic (hardened) and magnetic; non-magnetic austenitic grades cannot be hardened enough for raceways and balls.
Where is W625 typically used?
Food and packaging machines, pharmaceutical equipment, washdown conveyors, chemical and marine-atmosphere drives and appliances exposed to moisture.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.