W627-6-ZZ bearing: complete specifications & equivalents
The W627-6-ZZ is a ISO 15 radial bearing sized 6 x 10 x 3 mm (bore x OD x width) with ZZ sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 6 mm |
| Outer diameter D | 10 mm |
| Width B | 3 mm |
| Material | SS440C |
| Seal / shield | ZZ |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | steel, stamped ribbon (J-type) |
| Basic dynamic load rating C | 0.286 kN |
| Basic static load rating C0 | 0.112 kN |
| Fatigue load limit Pu | 0.005 kN |
| Reference speed (thermal) | 120000 rpm |
| Limiting speed (mechanical) | 60000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 0.72 g |
| Manufacturer designation | W 627/6-2Z |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 6200-series range
| Bore d | 0.236 in |
|---|---|
| Outer diameter D | 0.394 in |
| Width B | 0.118 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 2 mm |
| Smallest bore in 6200-series | 3 mm |
| Largest outer diameter in 6200-series | 540 mm |
| Width range across 6200-series | 2.5–85 mm |
| Bore position in 6200-series (smallest first) | 4 of 45 |
| Bore above smallest 6200-series size | 3 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the W627-6-ZZ model number is decoded
The W prefix denotes SKF stainless steel deep-groove bearings (X108CrMo17 / AISI 440C class rings). In the 6200-series, the bore is written directly after the slash as 6 mm (bores below 10 mm use the slash spelling). Envelope 6×10×3 mm (0.236×0.394×0.118 in), C 0.286 kN, C0 0.112 kN, Pu 0.005 kN; limiting speed 60000 r/min and mass 0.72 g. SKF spells the double shield W 627/6-2Z (suffix 2Z); the shields are non-contact, retain grease and block coarse debris but are not liquid-tight. Stainless is chosen for corrosion and washdown duty, not for extra load — the same-envelope chrome-steel bearing rates higher.
Typical equipment & failure modes
Common applications
- bicycle and outdoor equipment
- appliances exposed to moisture
- food and beverage conveyors
- pharmaceutical and packaging machines
Known failure patterns
- seal and grease failure before the rings corrode in sustained washdown service
- surface staining and pitting when even the stainless steel is left unlubricated in salty or acidic duty
- fine-particle abrasion when non-contact shields let dust through in a dirty environment
- grease aging inside the shielded cavity with no relubrication path
Selection pitfalls — read before you substitute
- Temperatures above roughly 300 °C temper the stainless races; even standard greases fail far earlier — keep W627-6-ZZ inside the quoted grease temperature range.
- W-prefix stainless rings (X108CrMo17 / AISI 440C class) resist moisture and weak chemicals but will still rust in chloride-rich or salt-spray duty without protection — W627-6-ZZ is not marine-grade stainless.
- The stainless steel is martensitic and MAGNETIC; do not reject W627-6-ZZ over magnetism — only austenitic grades are non-magnetic, and those are too soft for bearing raceways.
- Stainless bearings carry lower load ratings than chrome steel of the same envelope: W627-6-ZZ is quoted at C 0.286 kN versus the 3 mm-wide 52100 version — do not swap on dimensions alone.
- Catalogue ratings for W627-6-ZZ (C 0.286 kN, C0 0.112 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
- Fillet radii must clear the W627-6-ZZ chamfer so the 3 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
Frequently asked questions
What are the dimensions of the stainless W627-6-ZZ?
SKF W 627/6-2Z measures 6×10×3 mm (0.236×0.394×0.118 in), about 0.72 g, C 0.286 kN.
What does the W in W 627/6-2Z mean?
W is the SKF prefix for stainless steel deep-groove bearings (rings in X108CrMo17 / AISI 440C class); the rest of the designation follows the normal series and bore rules.
What grease is supplied in W627-6-ZZ?
Sealed units are pre-greased for life; for food or pharmaceutical duty order (or re-grease before service) with an NSF H1 registered food-grade grease.
Are W stainless bearings waterproof?
No — the stainless rings resist moisture and weak chemicals far better than 52100 chrome steel, but salt spray, strong chlorides and unlubricated washdown duty can still corrode W627-6-ZZ; add seals and food-grade grease for wet positions.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.