62306-2RS bearing: complete specifications & equivalents

The 62306-2RS is a ISO 15 radial bearing sized 30 x 72 x 27 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 72 mm d = 30 B = 27 mm side section front view
Principal dimensions: bore d 30 mm, outer diameter D 72 mm, width B 27 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 30 mm
Outer diameter D 72 mm
Width B 27 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 28.1 kN
Basic static load rating C0 16 kN
Fatigue load limit Pu 0.67 kN
Limiting speed (mechanical) 6300 rpm
Operating temperature -40 to +120 °C
Mass 500 g
Manufacturer designation 62306-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 62300-series range

Bore d1.181 in
Outer diameter D2.835 in
Width B1.063 in
ISO bore code06
Radial section height (D−d)/221 mm
Smallest bore in 62300-series10 mm
Largest outer diameter in 62300-series150 mm
Width range across 62300-series17–51 mm
Bore position in 62300-series (smallest first)7 of 15
Bore above smallest 62300-series size20 mm

Cross references & equivalents

Equivalent modelBrandMatch levelNote
4306-ATN9 SKF partial
Main dimensions match; tolerances, seals or internal clearance differ.
Same 30×72×27 mm envelope as SKF 4306 ATN9, but catalogue C/C0 differ (28.1/16 kN vs 41/30 kN) — envelope match only after a load check.

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 62306-2RS model number is decoded

The 62300-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 62306 carries code 06 = 30 mm (code × 5). The envelope is 30×72×27 mm (1.181×2.835×1.063 in) with a 21.0 mm radial section height, C 28.1 kN, C0 16 kN and Pu 0.67 kN. SKF catalogues the sealed execution as 62306-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 6300 r/min, catalogue mass 500 g.

Typical equipment & failure modes

Common applications

  • centrifugal pumps
  • small gearboxes
  • conveyor drives
  • fans and blowers

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • raceway smearing under marginal lubrication at start-up
  • electrical pitting in VFD-driven motors without shaft grounding

Selection pitfalls — read before you substitute

  • Clearance suffixes follow the seal code in the designation stack (e.g. 62306-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Clearance suffixes follow the seal code in the designation stack (e.g. 62306-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Contact seals make 62306-2RS slower than the open 62306 (limiting 6300 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 62306-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • The fatigue load limit is 0.67 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
  • Fillet radii must clear the 62306-2RS chamfer so the 27 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
  • For positions that need relubrication, choose the open execution of 62306 and design the housing with a grease path; shielded and sealed versions are intended as fit-and-forget units.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 62306-2RS?

The SKF 62306-2RS1 measures 30 mm bore × 72 mm OD × 27 mm width (1.181 × 2.835 × 1.063 in), mass about 500 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 62306 work?

The final two digits of 62306 are bore code 06, multiplied by 5 to give 30 mm.

What internal clearance does 62306-2RS have?

Standard supply is normal CN radial clearance unless a suffix states otherwise; for tight fits or hot shafts SKF lists the C3 execution of the same size — the residual clearance left after mounting is what governs running life.

How long can a greased 62306-2RS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 62306-2RS take?

Catalogue values for 62306-2RS1: dynamic C 28.1 kN, static C0 16 kN, fatigue limit Pu 0.67 kN. Use C in life calculation and C0 for static checks at 30 mm bore.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.