6313-2RS-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6313-2RS-NTN model number is decoded

In the 6300-series (diameter series 3 of ISO 15) the last two digits encode the bore: 6313 carries bore code 13 = 65 mm. Outside diameter 140 mm and width 33 mm come from the ISO 15 boundary-dimensions general plan. Suffix -2RS denotes two contact-type elastomer seals over a lifetime grease fill; the sealing lips add drag compared with open or shielded versions. For normal-load mounting with a rotating inner ring on a 65 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. NTN's contact-seal catalogue number is 6313LLU (suffix LLU, or LLH low-torque variant), mapped here from the industry-neutral -2RS spelling; the contacting lip lowers the speed ceiling versus the open bearing.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Interference on a 65 mm shaft plus running heat consumes radial clearance: where the shaft runs hot or the fit is tight, order 6313 with C3 clearance and re-check the residual value after mounting.
• The 63xx medium section at 65 mm bore gains dynamic rating through larger rolling elements on a 140 mm OD; the penalty is mass and a lower limiting speed than the 6213 — do not specify it for speed-critical shafts.
• Heat is the enemy of the sealed 6313-2RS: sustained running near the lip temperature limit hardens the rubber, after which grease escapes and dirt tracks in — watch the housing temperature in hot drives.
• Never wash a sealed 6313-2RS-NTN in solvent or press it home via the outer ring; solvent destroys the grease thickener and mounting force through the seal deforms the lip.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 140 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6313-2RS-NTN.
• Vibration during standstill brinells the raceways of a 65 mm bearing at ball spacing; if the machine sits idle next to running equipment, turn the shaft over periodically or isolate the arrangement.
• NTN catalogues the contact-sealed version as 6313LLU (suffix LLU), mapped here from the industry-neutral -2RS spelling; it is greased for life and the contacting lip lowers the speed ceiling versus the open bearing.
• At 65 mm bore 6313 is in NTN's upper general-purpose range; the pressed-steel cage is standard but mid-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NTN channel if the application sees impact loads.
• NTN lists the grease limiting speed at 3300 r/min for 6313; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• At 103 kN dynamic load rating (C) and 60 kN static (C0), 4.6 kN fatigue load limit Cu, 6313 is a heavy-load bearing for industrial gearboxes and large conveyors; NTN expects a machined brass cage (suffix M) at this rating for shock duty, and the static C0 must be checked against any mounting or lifting loads.
• At 2080 g (2.1 kg), 6313 needs mechanical handling for mounting; NTN recommends induction heating the inner ring (max 120 °C) rather than pressing cold, and a lifting eye if the housing is pre-assembled.
• The 65×140×33 mm envelope of 6313 gives a D/d ratio of 2.15 and 37.5 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 103/60 kN load ratings, 4.6 kN fatigue load limit Cu NTN lists the grease limiting speed at 3300 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 2080 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6313LLU on the 65×140×33 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6313 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• NTN's pressed-steel cage (no cage suffix) is the quiet standard for this size; for sustained running close to the limiting speed or for heavy shock duty, ask the NTN channel whether a machined-cage execution of 6313 is listed.