6319-NSK bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6319-NSK model number is decoded

In the 6300-series (diameter series 3 of ISO 15) the last two digits encode the bore: 6319 carries bore code 19 = 95 mm. Outside diameter 200 mm and width 45 mm come from the ISO 15 boundary-dimensions general plan. With no seal suffix the bearing is open: no shields or seals are fitted and lubrication is supplied by the application. For normal-load mounting with a rotating inner ring on a 95 mm shaft, typical catalogue practice is a k5 shaft seat with an H7 housing bore — verify against the actual load direction and magnitude. In the NSK catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Large bores like the 95 mm of 6319-NSK demand clean, burr-free seats; one raised burr under a ring this size cocks the bearing and concentrates load at the raceway edge, cutting life drastically.
• The 63xx medium series gains rating at 95 mm bore through a 200 mm OD and 45 mm width; the heavier rolling elements also trade away some speed versus a 6219.
• The open 6319-NSK has no lubricant retention: grease escapes and contaminants migrate straight into the 95×200×45 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6319 units.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 200 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6319-NSK.
• Suffixes stack in a defined order — clearance follows the seal code, e.g. 6319-NSK-C3. No clearance suffix means normal CN clearance.
• The open 6319 has no integral sealing; in the NSK E1103 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), VV (non-contact rubber seals) and DDU (contact rubber seals). NSK does not offer a low-torque contact seal equivalent to NTN's LLH in this catalogue — for high-speed sealed duty specify the VV non-contact seal and an external housing labyrinth.
• At 95 mm bore 6319 is in NSK's medium industrial range; the pressed-steel cage is standard, but large-section 63xx sizes at this bore can be ordered with a machined brass cage (suffix M) for heavy-shock or very-low-speed duty — confirm cage material with the NSK channel if the application sees impact loads.
• NSK rates 6319 at 168 kN dynamic (C) and 119 kN static (C0); this heavy-load rating is at the upper end of the E1103 Part C single-row deep-groove extract — NSK supplies a machined brass cage (suffix M) and expects an application review, because catalogue L10 life alone does not capture shock and misalignment loads at this rating.
• At 5760 g (5.8 kg), 6319 is a heavy NSK bearing that requires a crane or hoist for handling; induction-heat the inner ring (max 120 °C) and use a mechanical puller for removal — never apply heat directly to the balls or cage.
• The 95×200×45 mm envelope of 6319 gives a D/d ratio of 2.11 and 52.5 mm radial section height — a heavy NSK section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 168/119 kN load ratings, mass 5760 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6319 on the 95×200×45 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6319 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• When replacing a failed unit, inspect the shaft and housing seats before fitting the new 6319 — a new bearing pressed onto a worn or oval seat reproduces the original failure mode in a fraction of its expected life.
• Keep NSK bearings in the original packaging until fitting: the wrapper carries the production lot, and the unopened shelf life of greased sealed units is typically quoted at three to five years in dry, vibration-free storage.