6330-ZZ bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NSK Rolling Bearings E1103 Part C) · extracted 2026-09-24

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6330-ZZ model number is decoded

6330-ZZ carries two non-contact sheet-steel shields that hold the factory grease in and keep coarse debris out; they do not seal against liquids. Within the medium 63xx section (diameter series 3 of ISO 15), multiplying bore code 30 by five gives the 150 mm bore; the 320 mm outside diameter and 65 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 150 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. NSK catalogue order number: 6330ZZ (suffix ZZ), two non-contact steel shields, mapped here from the industry-neutral -ZZ spelling.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Mount this 150 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
• The 63xx medium series gains rating at 150 mm bore through a 320 mm OD and 65 mm width; the heavier rolling elements also trade away some speed versus a 6230.
• Do not wash 6330-ZZ in solvent before mounting: the grease inside the shielded cavity is the service fill, and solvent creeping past the shield gap strips it out.
• Shielded 6330-ZZ units are typically greased for life; prying the shields out for regreasing usually bends them and leaves a gap that throws grease in service.
• Measure the shaft, do not trust the drawing: a 150 mm nominal journal worn by even 0.02 mm turns an interference seat into a creeping fit that frets the bore of 6330-ZZ.
• Deep-groove ball bearings tolerate only minutes of misalignment; if the 320 mm housing cannot be aligned, switch to a self-aligning type rather than shimming 6330-ZZ.
• NSK catalogues the shielded version as 6330ZZ — suffix ZZ, two non-contact steel shields. The industry-neutral page spelling is -ZZ; quote the NSK order number when buying through an NSK channel.
• The 150 mm bore places 6330 at the lower end of NSK's large-size range; at these diameters the pressed-steel cage is speed-limited and NSK commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NSK distributor, and do not extrapolate small-bore speed ratings to this size.
• NSK rates 6330 at 300 kN dynamic (C) and 284 kN static (C0); this is an extreme-load bearing at the top of the E1103 Part C single-row deep-groove range, where mounting, shaft stiffness and housing alignment dominate the achievable life. Consult NSK engineering for a full application review rather than relying on catalogue L10 alone.
• At 22700 g (22.7 kg), 6330 is a very heavy NSK bearing where handling and mounting method directly affect service life; NSK requires induction heating of the inner ring (max 120 °C), a mechanical puller for removal, and a defined lifting procedure to avoid damaging the cage.
• The 150×320×65 mm envelope of 6330 gives a D/d ratio of 2.13 and 85.0 mm radial section height — a heavy NSK section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 300/284 kN load ratings, mass 22700 g here are NSK Rolling Bearings E1103 Part C catalogue figures for 6330ZZ on the 150×320×65 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6330 in a rated drive. NSK does not tabulate reference or limiting speeds in the E1103 Part C dimension tables used for this page — consult NSK's separate speed-rating tables before high-speed service.
• Standard P0 runout from NSK is adequate up to the catalogue limiting speed on ground shaft seats; spindle or instrument positions should specify P6/P5 accuracy explicitly — it is a different order code, not a sorting of standard stock.
• NSK supplies its sealed units pre-greased for general duty between roughly -10 and +110 °C; low-temperature, food-grade and high-temperature fills are special executions — ask at order time, because DDU/VV units are not designed to be opened and repacked.