150×320×65 mm bearings

19 models from 3 brands across 3 types share this ISO 15 envelope: 150 mm bore, 320 mm outside diameter, 65 mm width (5.906×12.598×2.559 in), 85 mm radial section.

19 models fit this space 3 brands 19 with catalogue C rating

Dimensional interchange — verify before substituting

These bearings are interchangeable on boundary dimensions per ISO 15 — same bore, OD and width. They are not guaranteed drop-in equivalents: compare load ratings, seals, clearance, cage, precision and axial-locating design for the specific duty. Models without a catalogue C rating on this site carry ISO 15 geometry only; request the manufacturer table before a load-critical replacement.

Model Type Brand Seal Clearance C (kN) C0 (kN) Mass (g)
6330 Deep Groove Ball SKF open CN 276 285 23000
6330-M Deep Groove Ball SKF open CN 276 285 25500
6330-NSK Deep Groove Ball NSK open CN 300 284 22700
6330-NTN Deep Groove Ball NTN open CN 305 284 22000
6330-ZZ Deep Groove Ball NSK ZZ CN 300 284 22700
7330 Angular Contact Ball NTN open CN 365 380 25100
7330-BCBM Angular Contact Ball SKF open CN 332 390 26000
7330B Angular Contact Ball NTN open CN 335 350 25100
N330 Cylindrical Roller NTN open CN 735 805 24700
NF330 Cylindrical Roller NTN open CN 735 805 24700
NJ330 Cylindrical Roller NTN open CN 735 805 24700
NJ330-ECML Cylindrical Roller SKF open CN 900 965 26500
NJ330E Cylindrical Roller NTN open CN 840 920 —
NU330 Cylindrical Roller NTN open CN 735 805 24700
NU330-ECM Cylindrical Roller SKF open CN 900 965 26500
NU330E Cylindrical Roller NTN open CN 840 920 —
NUP330 Cylindrical Roller NTN open CN 735 805 24700
NUP330E Cylindrical Roller NTN open CN 840 920 —
QJ-330-N2MA Angular Contact Ball SKF open CN 530 765 29000

Note: catalogue dynamic load ratings for this envelope span 276.0– 900.0 kN — a 226% spread between designs in the very same 150×320×65 mm space. The higher-rated unit is not an upgrade for every duty (it may run at lower limiting speed), but ignoring the gap will over- or under-life the replacement.

Substitution verification checklist

  1. Load rating. Check C (dynamic) and C0 (static) against the original life calculation — the table above shows which models carry verified catalogue values.
  2. Sealing. Open, -ZZ shields and -2RS contact seals are not equivalent in friction, speed or contamination protection; match the housing environment, not just the suffix on the old box.
  3. Internal clearance. CN/C3/C4 changes with fit and operating temperature; an interference inner-ring mount commonly needs C3 where the bench bearing ran CN.
  4. Cage and precision. Stamped steel, machined brass and polymer cages, and P0/P6/P5 tolerance classes, carry different speed and shock limits.
  5. Locating behaviour. Within one envelope an NU cylindrical roller floats axially while an NJ/NUP locates; ball designs take thrust that roller locating schemes do not. Preserve the shaft's locating arrangement.

Browse all 150 mm bore bearings for wider or narrower sections, or open a model page for naming-rule decode, applications and graded cross references: 6330, 6330-M, 6330-NSK, 6330-NTN, 6330-ZZ, 7330, 7330-BCBM, 7330B, N330, NF330, NJ330, NJ330-ECML, NJ330E, NU330, NU330-ECM, NU330E, NUP330, NUP330E, QJ-330-N2MA.

Frequently asked questions

Are all 150×320×65 mm bearings interchangeable?

They share the same ISO 15 boundary dimensions — 150 mm bore, 320 mm OD, 65 mm width (5.906×12.598×2.559 in) — so they fit the same shaft, housing bore and axial space. Interchangeability ends at the envelope: dynamic load rating, seal arrangement, internal clearance, cage and precision class differ between the 19 models listed here and must be checked against the duty before substitution.

Is it a drop-in replacement if two bearings both measure 150×320×65?

Only after verification. Confirm five things in order: (1) the C/C0 load ratings meet the original life calculation, (2) the seal type is equivalent or acceptable for the contamination level (open vs -ZZ vs -2RS), (3) internal clearance matches (CN/C3/C4 — an interference fit changes residual play), (4) cage material and precision class suit the speed, and (5) the axial-locating behaviour is the same (for example an NU cylindrical roller floats while an NJ locates one way). Same dimensions alone never guarantee equal performance.

What is 150×320×65 mm in inches?

150×320×65 mm converts to 5.906×12.598×2.559 in, with a 85 mm (3.346 in) radial section height. These are the ISO 15 general-plan envelope dimensions shared across manufacturers, which is why models such as 6330, 6330-M, 6330-NSK mount in the same space despite different internal designs.