6336-NTN bearing: complete specifications & equivalents

Specification table

Source: catalog reference (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)) · extracted 2026-09-25

Parameters extracted from the official NTN Ball and Roller Bearings catalogue (NTN Ball and Roller Bearings CAT.No.2203-3/E (2024)); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the 6336-NTN model number is decoded

6336 is supplied open, without shields or seals, so the arrangement around it must supply and retain the lubricant. Within the medium 63xx section (diameter series 3 of ISO 15), multiplying bore code 36 by five gives the 180 mm bore; the 380 mm outside diameter and 75 mm width follow the same boundary-dimension plan. For a rotating inner ring on a 180 mm shaft under normal load, catalogue practice seats it on a m6 shaft fit with an H7 housing bore — confirm against the actual load direction and magnitude before committing. In the NTN catalogue this open execution carries the bare designation; protected variants are ordered separately with suffixes ZZ (shields), LLB/LLF (non-contact seals), LLH (low-torque contact seal) and LLU (contact seal).

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• At 180 mm bore the ring mass is significant: heat 6336 on an induction heater (max 120 °C), never over an open flame, and plan puller access or a withdrawal sleeve now for the day it has to come off again.
• The 63xx medium series gains rating at 180 mm bore through a 380 mm OD and 75 mm width; the heavier rolling elements also trade away some speed versus a 6236.
• The open 6336-NTN has no lubricant retention: grease escapes and contaminants migrate straight into the 180×380×75 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
• Open bearings tolerate the highest speeds in the 6300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 6336 units.
• Shaft and housing fillets must clear the bearing chamfer so the 75 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
• Assign fits by which ring rotates: an interference shaft fit for a rotating inner ring; if the outer ring rotates instead, reverse the logic — a loose rotating ring creeps and frets its seat.
• The open 6336 has no integral sealing; in the NTN 2203 catalogue the protected variants carry suffixes ZZ (non-contact steel shields), LLB/LLF (non-contact rubber seals), LLU (contact rubber seals) and LLH (a low-torque contact seal with higher speed capability than LLU). A JR or JRX suffix (printed for some thin-section sizes) denotes a pressed-steel cage, not a seal.
• The 180 mm bore places 6336 in NTN's large-size range; at these diameters the pressed-steel cage is speed-limited and NTN commonly supplies a machined brass cage (suffix M) as an option. Verify cage material and relubrication interval with the NTN distributor, and do not extrapolate small-bore speed ratings to this size.
• NTN lists the grease limiting speed at 1700 r/min for 6336; this is a large or heavy-section size where centrifugal force and cage inertia cap the speed — for higher shaft speeds either step to a smaller bearing on the same bore or consult NTN for an oil-lubricated, machined-cage variant.
• NTN rates 6336 at 390 kN dynamic (C) and 405 kN static (C0), 19 kN fatigue load limit Cu; this is an upper heavy-load rating where the pressed-steel cage is not recommended — NTN supplies a machined brass cage (suffix M) and the static C0 must be verified against any shock or lifting loads the bearing sees during mounting.
• At 35600 g (35.6 kg), 6336 is a very heavy bearing where handling and mounting method directly affect service life; NTN requires induction heating of the inner ring (max 120 °C), a mechanical puller for removal, and a defined lifting procedure to avoid damaging the machined brass cage.
• The 180×380×75 mm envelope of 6336 gives a D/d ratio of 2.11 and 100.0 mm radial section height — a heavy section built for high-load, lower-speed duty; specifying it in a high-rpm motor generates excess heat and shortens grease life, so prefer a 62/63-series there.
• The 390/405 kN load ratings, 19 kN fatigue load limit Cu NTN lists the grease limiting speed at 1700 r/min for this designation; oil-mist or jet lubrication raises the ceiling but requires a sealed-housing review. and 35600 g mass here are NTN Ball and Roller Bearings CAT.No.2203-3/E figures for 6336 on the 180×380×75 mm ISO 15 envelope; internal geometry and ratings legitimately differ between brands, so re-verify before substituting another manufacturer's 6336 in a rated drive.
• NTN date-codes its packaging; rotate stock first-in-first-out, because the grease inside sealed units ages on the shelf — after three to five years of storage, check the grease condition before putting the bearing into service.
• Factory-fill grease in NTN sealed units is a general-duty lithium-soap grease; food-grade, low-temperature and high-temperature fills are request options at order time, because LLU/LLB units are not meant to be opened and re-greased in the field.