63004-2RS bearing: complete specifications & equivalents

The 63004-2RS is a ISO 15 radial bearing sized 20 x 42 x 16 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.

Bearing dimension schematic Front view shows outer diameter D and bore d; side section shows width B. D = 42 mm d = 20 B = 16 mm side section front view
Principal dimensions: bore d 20 mm, outer diameter D 42 mm, width B 16 mm. Schematic, not to scale.

Specification table

ParameterValue
Brand SKF
Bore diameter d 20 mm
Outer diameter D 42 mm
Width B 16 mm
Material GCr15
Seal / shield 2RS
Internal clearance CN
Tolerance class P0
Cage steel, stamped ribbon (J-type)
Basic dynamic load rating C 9.36 kN
Basic static load rating C0 5 kN
Fatigue load limit Pu 0.212 kN
Limiting speed (mechanical) 11000 rpm
Operating temperature -40 to +120 °C
Mass 86 g
Manufacturer designation 63004-2RS1
Standard ISO 15
Catalog version SKF PUB BU/P1 17000/1 EN (Oct 2018)
Last verified 2026-09-27

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Dimensions in inches & 63000-series range

Bore d0.787 in
Outer diameter D1.654 in
Width B0.63 in
ISO bore code04
Radial section height (D−d)/211 mm
Smallest bore in 63000-series10 mm
Largest outer diameter in 63000-series80 mm
Width range across 63000-series12–23 mm
Bore position in 63000-series (smallest first)5 of 11
Bore above smallest 63000-series size10 mm

Cross references & equivalents

No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.

How the 63004-2RS model number is decoded

The 63000-series is the wide-section counterpart of the standard deep-groove family (extra width code built into the designation); the last two digits encode the bore: 63004 carries code 04 = 20 mm (code × 5). The envelope is 20×42×16 mm (0.787×1.654×0.63 in) with a 11.0 mm radial section height, C 9.36 kN, C0 5 kN and Pu 0.212 kN. SKF catalogues the sealed execution as 63004-2RS1: two contact elastomer lips (2RS1/2RSH spelling) over a lifetime grease fill; the lips add drag, and no reference (thermal) speed is published. Limiting speed 11000 r/min, catalogue mass 86 g.

Typical equipment & failure modes

Common applications

  • conveyor drives
  • fans and blowers
  • agricultural equipment
  • garden machinery

Known failure patterns

  • contact-seal lip hardening and pre-grease loss after long high-temperature service
  • grease-life expiry inside the sealed-for-life cavity, which has no relubrication path
  • fretting corrosion on a creeping shaft or housing seat
  • cage damage from running beyond the limiting speed

Selection pitfalls — read before you substitute

  • Clearance suffixes follow the seal code in the designation stack (e.g. 63004-2Z/C3 in SKF spelling); no suffix means normal CN internal clearance.
  • Deep-groove geometry tolerates only minutes of misalignment; if the 42 mm housing bore cannot be aligned, move to a self-aligning bearing rather than shimming 63004-2RS.
  • Contact seals make 63004-2RS slower than the open 63004 (limiting 11000 r/min) and forbid solvent washing, which destroys the lifetime grease.
  • Do not pry the caps off 63004-2RS to repack it; shield/seal damage leaves a gap that throws grease and admits dirt.
  • At 20 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
  • Catalogue ratings for 63004-2RS (C 9.36 kN, C0 5 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
  • For positions that need relubrication, choose the open execution of 63004 and design the housing with a grease path; shielded and sealed versions are intended as fit-and-forget units.
  • Sealed SKF units are filled with a lithium-based grease for general service; food-grade, low-temperature and high-temperature fills are order options and are not field-interchangeable once the unit is sealed.

Frequently asked questions

What are the dimensions of 63004-2RS?

The SKF 63004-2RS1 measures 20 mm bore × 42 mm OD × 16 mm width (0.787 × 1.654 × 0.63 in), mass about 86 g. It has two contact rubber seals and a lifetime grease fill.

How does the bore code in 63004 work?

The final two digits of 63004 are bore code 04, multiplied by 5 to give 20 mm.

How long can a greased 63004-2RS be stored?

Sealed and shielded SKF units carry a finite grease shelf life: SKF recommends first-in-first-out stock rotation and dry, cool, vibration-free storage. Open units ship with rust preventive only and are greased at assembly.

What load can 63004-2RS take?

Catalogue values for 63004-2RS1: dynamic C 9.36 kN, static C0 5 kN, fatigue limit Pu 0.212 kN. Use C in life calculation and C0 for static checks at 20 mm bore.

What is the speed rating of 63004-2RS?

SKF publishes only the 11000 r/min limiting speed for this execution; sealed variants have no thermal reference speed because seal and grease life govern.

Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.