1205-ETN9 bearing: complete specifications & equivalents
The 1205-ETN9 is a ISO 15 radial bearing sized 25 x 52 x 15 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 25 mm |
| Outer diameter D | 52 mm |
| Width B | 15 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 14.3 kN |
| Basic static load rating C0 | 4 kN |
| Fatigue load limit Pu | 0.21 kN |
| Reference speed (thermal) | 28000 rpm |
| Limiting speed (mechanical) | 18000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 140 g |
| Manufacturer designation | 1205 ETN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 1200-series range
| Bore d | 0.984 in |
|---|---|
| Outer diameter D | 2.047 in |
| Width B | 0.591 in |
| ISO bore code | 05 |
| Radial section height (D−d)/2 | 13.5 mm |
| Smallest bore in 1200-series | 6 mm |
| Largest outer diameter in 1200-series | 230 mm |
| Width range across 1200-series | 6–154 mm |
| Bore position in 1200-series (smallest first) | 10 of 32 |
| Bore above smallest 1200-series size | 19 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 1205 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 25×52×15 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 1205-EKTN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 25×52×15 mm envelope with catalogue ratings within 10 %; 1205 EKTN9 is the glass-fibre PA66 cage, open arrangement, tapered bore execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
| 11205-ETN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 25×52×15 mm envelope with catalogue ratings within 10 %; 11205 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 1205-ETN9 model number is decoded
The 12xx series is the light/normal-section self-aligning ball bearing (ISO dimension series 02). the last two digits encode the bore: 1205 carries code 05 = 25 mm (code × 5). Envelope 25×52×15 mm (0.984×2.047×0.591 in) with a 13.5 mm radial section height, C 14.3 kN, C0 4 kN and Pu 0.21 kN. The open 1205 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 25 mm shaft. Reference (thermal) speed 28000 r/min, limiting speed 18000 r/min, catalogue mass 140 g.
Typical equipment & failure modes
Common applications
- conveyor idler rollers
- agricultural machinery shafts
- textile spindles and looms
- fan and blower shafts
Known failure patterns
- contamination wear when the open arrangement is used without adequate external sealing
- lubricant starvation where no regreasing interval is maintained
- brinelling from static overload or hammer blows during mounting
- false brinelling from vibration while the shaft stands idle
Selection pitfalls — read before you substitute
- The spherical outer raceway lets 1205-ETN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.
- The fatigue load limit is 0.21 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- The ETN9 suffix on 1205-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 18000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- Fillet radii must clear the 1205-ETN9 chamfer so the 15 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1205-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- Assign interference to the rotating ring: on a 25 mm rotating shaft use a k5 seat with an H7 housing; reverse the logic if the outer ring rotates.
Frequently asked questions
What are the dimensions of 1205-ETN9?
SKF 1205 ETN9 measures 25 mm bore × 52 mm OD × 15 mm width (0.984 × 2.047 × 0.591 in), mass about 140 g. It is open, with no shields or seals.
How does the bore code in 1205 work?
The final two digits of 1205 are bore code 05, multiplied by 5 to give 25 mm.
What is the speed rating of 1205-ETN9?
SKF lists a 28000 r/min thermal reference speed and a 18000 r/min mechanical limiting speed for 1205 ETN9; real limits also depend on lubrication and fits.
How much misalignment can 1205-ETN9 tolerate?
Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1205-ETN9 allow less (about 1°) because the seal lip binds first.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.