1220K bearing: complete specifications & equivalents
The 1220K is a ISO 15 radial bearing sized 100 x 180 x 34 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 100 mm |
| Outer diameter D | 180 mm |
| Width B | 34 mm |
| Seal / shield | open |
| Basic dynamic load rating C | 69.5 kN |
| Basic static load rating C0 | 29.7 kN |
| Fatigue load limit Pu | 1.2 kN |
| Limiting speed (mechanical) | 3200 rpm |
| Mass | 3740 g |
| Manufacturer designation | 1220SK |
| Standard | ISO 15 |
| Catalog version | CAT. No. 2203-3/E 2024 |
| Last verified | 2026-09-25 |
Source: catalog reference (CAT. No. 2203-3/E 2024) · extracted 2026-09-25
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (CAT. No. 2203-3/E 2024); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 1200-series range
| Bore d | 3.937 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 1.339 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 40 mm |
| Smallest bore in 1200-series | 10 mm |
| Largest outer diameter in 1200-series | 200 mm |
| Width range across 1200-series | 9–38 mm |
| Bore position in 1200-series (smallest first) | 21 of 23 |
| Bore above smallest 1200-series size | 90 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 1220K model number is decoded
In the 1200-series (ISO 15 dimension series) the leading digits 12 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1220 carries bore code 20 = 100 mm. Outside diameter 180 mm and width 34 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 1220. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.
Typical equipment & failure modes
Common applications
- hoist, winch and crane drums
- heavy conveyor drive shafts
- pulp, paper and steel mill machinery
- heavy industrial drive shafts
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- fretting corrosion on a loose shaft seat
- rolling-contact fatigue spalling after the rated L10 life is exceeded
Selection pitfalls — read before you substitute
- Mount this 100 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 12xx light section at 100 mm bore uses a smaller 180 mm OD than a 1320; load ratings are lower, so do not replace a failed 13-series bearing with a 12-series without re-rating the load.
- Tapered-bore 1220K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 100 mm shaft before ordering.
- The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.
- Suffixes stack in a defined order — clearance follows the bore code, e.g. 1220-C3. No clearance suffix means normal CN clearance.
Frequently asked questions
What are the dimensions of a 1220K self-aligning ball bearing?
A 1220K self-aligning ball bearing has a 100 mm bore, 180 mm outer diameter and 34 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 1220.
How does the 1220 bore code work?
The last two digits of 1220 are bore code 20, giving 20 × 5 = 100 mm bore. The 180 mm outside diameter and 34 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the K suffix mean on 1220K?
The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 1220. Adapter sleeves are sold separately and must match the bore code.
How does the 1200 compare with other self-aligning series at the same 100 mm bore?
The 12xx is the light section: 180×34 mm with a 40.0 mm radial section at 100 mm bore — below 13/22/23 in load capacity, for light loads in compact spaces.
Reviewed & verified by the MPN Base engineering desk against source catalog CAT. No. 2203-3/E 2024 on 2026-09-25. Read our editorial & correction policy.