1303-ETN9 bearing: complete specifications & equivalents
The 1303-ETN9 is a ISO 15 radial bearing sized 17 x 47 x 14 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 17 mm |
| Outer diameter D | 47 mm |
| Width B | 14 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 12.7 kN |
| Basic static load rating C0 | 3.4 kN |
| Fatigue load limit Pu | 0.18 kN |
| Reference speed (thermal) | 28000 rpm |
| Limiting speed (mechanical) | 20000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 120 g |
| Manufacturer designation | 1303 ETN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 1300-series range
| Bore d | 0.669 in |
|---|---|
| Outer diameter D | 1.85 in |
| Width B | 0.551 in |
| ISO bore code | 03 |
| Radial section height (D−d)/2 | 15 mm |
| Smallest bore in 1300-series | 5 mm |
| Largest outer diameter in 1300-series | 320 mm |
| Width range across 1300-series | 6–74 mm |
| Bore position in 1300-series (smallest first) | 5 of 29 |
| Bore above smallest 1300-series size | 12 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 1303 | NTN | full Dimensions and internal design equivalent — standard interchange. | NTN counterpart 1303S on the same 17×47×14 mm envelope with ratings within 10 % — interchange after checking seal, cage and bore details on both pages. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 1303-ETN9 model number is decoded
The 13xx series is the medium/normal-section self-aligning ball bearing (ISO dimension series 03). bore code 03 follows the 10/12/15/17 mm exception table, so 1303 fits a 17 mm shaft. Envelope 17×47×14 mm (0.669×1.85×0.551 in) with a 15.0 mm radial section height, C 12.7 kN, C0 3.4 kN and Pu 0.18 kN. The open 1303 ETN9 carries no shields or seals and relies on application lubrication and external sealing. The ETN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The bore is cylindrical (straight), for a press-fit on a 17 mm shaft. Reference (thermal) speed 28000 r/min, limiting speed 20000 r/min, catalogue mass 120 g.
Typical equipment & failure modes
Common applications
- light gearbox layshafts
- food-processing conveyors
- small electric motors
- conveyor idler rollers
Known failure patterns
- lubricant starvation where no regreasing interval is maintained
- contamination wear when the open arrangement is used without adequate external sealing
- cage damage from running beyond the limiting speed
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.
- Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.
- The ETN9 suffix on 1303-ETN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 20000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 1303-ETN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- Assign interference to the rotating ring: on a 17 mm rotating shaft use a j5/k5 seat with an H7 housing; reverse the logic if the outer ring rotates.
- Catalogue ratings for 1303-ETN9 (C 12.7 kN, C0 3.4 kN) are SKF figures from PUB BU/P1 17000; geometry revisions can change ratings without changing the designation, so keep the catalogue edition with the specification.
Frequently asked questions
What are the dimensions of 1303-ETN9?
SKF 1303 ETN9 measures 17 mm bore × 47 mm OD × 14 mm width (0.669 × 1.85 × 0.551 in), mass about 120 g. It is open, with no shields or seals.
How does the bore code in 1303 work?
Codes 00–03 follow the exception table (10, 12, 15, 17 mm): 1303 fits a 17 mm shaft. Code × 5 starts at code 04.
How much misalignment can 1303-ETN9 tolerate?
Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 1303-ETN9 allow less (about 1°) because the seal lip binds first.
Can 1303-ETN9 take axial load?
A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.