1317 bearing: complete specifications & equivalents
The 1317 is a ISO 15 radial bearing sized 85 x 180 x 41 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 85 mm |
| Outer diameter D | 180 mm |
| Width B | 41 mm |
| Seal / shield | open |
| Basic dynamic load rating C | 98.5 kN |
| Basic static load rating C0 | 38 kN |
| Fatigue load limit Pu | 0.95 kN |
| Limiting speed (mechanical) | 3400 rpm |
| Mass | 5030 g |
| Manufacturer designation | 1317S |
| Standard | ISO 15 |
| Catalog version | CAT. No. 2203-3/E 2024 |
| Last verified | 2026-09-25 |
Source: catalog reference (CAT. No. 2203-3/E 2024) · extracted 2026-09-25
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (CAT. No. 2203-3/E 2024); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 1300-series range
| Bore d | 3.346 in |
|---|---|
| Outer diameter D | 7.087 in |
| Width B | 1.614 in |
| ISO bore code | 17 |
| Radial section height (D−d)/2 | 47.5 mm |
| Smallest bore in 1300-series | 10 mm |
| Largest outer diameter in 1300-series | 240 mm |
| Width range across 1300-series | 11–50 mm |
| Bore position in 1300-series (smallest first) | 18 of 23 |
| Bore above smallest 1300-series size | 75 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 1317 model number is decoded
In the 1300-series (ISO 15 dimension series) the leading digits 13 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 1317 carries bore code 17 = 85 mm. Outside diameter 180 mm and width 41 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.
Typical equipment & failure modes
Common applications
- large gearbox and reducer shafts
- industrial fan and blower rotors
- hoist, winch and crane drums
- heavy conveyor drive shafts
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- rolling-contact fatigue spalling after the rated L10 life is exceeded
- cage wear or fracture from sustained vibration or shock loading
Selection pitfalls — read before you substitute
- Mount this 85 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 13xx medium section at 85 mm bore gains rating through a larger 180 mm OD and 41 mm width; verify the housing accepts the larger envelope before substituting for a 1217.
- The open 1317 has no lubricant retention: grease escapes and contaminants migrate straight into the 85×180×41 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Open bearings tolerate the highest speeds in the 1300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 1317 units.
- Shaft and housing fillets must clear the bearing chamfer so the 41 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
Frequently asked questions
What are the dimensions of a 1317 self-aligning ball bearing?
A 1317 self-aligning ball bearing has a 85 mm bore, 180 mm outer diameter and 41 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting.
How does the 1317 bore code work?
The last two digits of 1317 are bore code 17, giving 17 × 5 = 85 mm bore. The 180 mm outside diameter and 41 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the open suffix mean on 1317?
A bare 1317 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication.
How does the 1300 compare with other self-aligning series at the same 85 mm bore?
The 13xx is the medium section: 180×41 mm, 47.5 mm radial section at 85 mm bore, carrying more load than a 1217 but needing a larger housing bore.
Reviewed & verified by the MPN Base engineering desk against source catalog CAT. No. 2203-3/E 2024 on 2026-09-25. Read our editorial & correction policy.