2209-EKTN9 bearing: complete specifications & equivalents
The 2209-EKTN9 is a ISO 15 radial bearing sized 45 x 85 x 23 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 45 mm |
| Outer diameter D | 85 mm |
| Width B | 23 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 32.5 kN |
| Basic static load rating C0 | 10.6 kN |
| Fatigue load limit Pu | 0.54 kN |
| Reference speed (thermal) | 15000 rpm |
| Limiting speed (mechanical) | 10000 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 550 g |
| Manufacturer designation | 2209 EKTN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 2200-series range
| Bore d | 1.772 in |
|---|---|
| Outer diameter D | 3.346 in |
| Width B | 0.906 in |
| ISO bore code | 09 |
| Radial section height (D−d)/2 | 20 mm |
| Smallest bore in 2200-series | 10 mm |
| Largest outer diameter in 2200-series | 200 mm |
| Width range across 2200-series | 14–53 mm |
| Bore position in 2200-series (smallest first) | 10 of 23 |
| Bore above smallest 2200-series size | 35 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 2209 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×85×23 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 2209-E-2RS1TN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (32.5/10.6 kN vs 22.9/7.8 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2209-E-2RS1KTN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 45×85×23 mm envelope, but catalogue C/C0 differ between executions (32.5/10.6 kN vs 22.9/7.8 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2209-ETN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 45×85×23 mm envelope with catalogue ratings within 10 %; 2209 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 2209-EKTN9 model number is decoded
The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2209 carries code 09 = 45 mm (code × 5). Envelope 45×85×23 mm (1.772×3.346×0.906 in) with a 20.0 mm radial section height, C 32.5 kN, C0 10.6 kN and Pu 0.54 kN. The open 2209 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 15000 r/min, limiting speed 10000 r/min, catalogue mass 550 g.
Typical equipment & failure modes
Common applications
- conveyor drum and pulley shafts
- agricultural gearboxes
- textile machinery drives
- industrial fans and blowers
Known failure patterns
- contamination wear when the open arrangement is used without adequate external sealing
- lubricant starvation where no regreasing interval is maintained
- adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder
- incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance
- fretting corrosion on a creeping shaft or housing seat
- cage damage from running beyond the limiting speed
Selection pitfalls — read before you substitute
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2209-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
- The fatigue load limit is 0.54 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- Tighten the adapter sleeve to the SKF-recommended starting clearance, not to feel — an over-tightened sleeve expands the inner ring and removes all internal clearance.
- The EKTN9 suffix on 2209-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 10000 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- The fatigue load limit is 0.54 kN; it feeds the equivalent-mean-load check, not the basic life calculation — do not substitute one for the other.
- At 45 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
Frequently asked questions
What are the dimensions of 2209-EKTN9?
SKF 2209 EKTN9 measures 45 mm bore × 85 mm OD × 23 mm width (1.772 × 3.346 × 0.906 in), mass about 550 g. It is open, with no shields or seals.
How does the bore code in 2209 work?
The final two digits of 2209 are bore code 09, multiplied by 5 to give 45 mm.
Can 2209-EKTN9 take axial load?
A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement.
Which fits should I use for 2209-EKTN9?
With a rotating inner ring use roughly k5 on the shaft and H7 in the 85 mm housing; reverse the interference if the outer ring rotates.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.