2210-E-2RS1KTN9 bearing: complete specifications & equivalents
The 2210-E-2RS1KTN9 is a ISO 15 radial bearing sized 50 x 90 x 23 mm (bore x OD x width) with 2RS sealing. Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 50 mm |
| Outer diameter D | 90 mm |
| Width B | 23 mm |
| Material | GCr15 |
| Seal / shield | 2RS |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 22.9 kN |
| Basic static load rating C0 | 8.15 kN |
| Fatigue load limit Pu | 0.42 kN |
| Limiting speed (mechanical) | 4800 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 570 g |
| Manufacturer designation | 2210 E-2RS1KTN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 2200-series range
| Bore d | 1.969 in |
|---|---|
| Outer diameter D | 3.543 in |
| Width B | 0.906 in |
| ISO bore code | 10 |
| Radial section height (D−d)/2 | 20 mm |
| Smallest bore in 2200-series | 10 mm |
| Largest outer diameter in 2200-series | 200 mm |
| Width range across 2200-series | 14–53 mm |
| Bore position in 2200-series (smallest first) | 11 of 23 |
| Bore above smallest 2200-series size | 40 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 2210 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×90×23 mm envelope per ISO 15; seal variant differs (2RS vs OPEN) — confirm sealing suits the duty. |
| 2210-E-2RS1TN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 50×90×23 mm envelope with catalogue ratings within 10 %; 2210 E-2RS1TN9 is the glass-fibre PA66 cage, two contact elastomer seals execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
| 2210-ETN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (22.9/8.15 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2210-EKTN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 50×90×23 mm envelope, but catalogue C/C0 differ between executions (22.9/8.15 kN vs 33.8/11.2 kN) — boundary dimensions match, not a load-rating equivalent. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 2210-E-2RS1KTN9 model number is decoded
The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2210 carries code 10 = 50 mm (code × 5). Envelope 50×90×23 mm (1.969×3.543×0.906 in) with a 20.0 mm radial section height, C 22.9 kN, C0 8.15 kN and Pu 0.42 kN. SKF spells the sealed execution 2210 E-2RS1KTN9 (suffix 2RS1): two contact elastomer lips over a lifetime grease fill; the lips add drag, and no thermal reference speed is published. The E-2RS1KTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Limiting speed 4800 r/min, catalogue mass 570 g.
Typical equipment & failure modes
Common applications
- agricultural gearboxes
- textile machinery drives
- industrial fans and blowers
- woodworking machinery
Known failure patterns
- fine dust or moisture passing a worn seal lip in dirty or wet duty
- grease loss when the sealed-for-life cavity is overheated with no relubrication path
- incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance
- adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder
- rolling-contact fatigue spalling once the catalogue L10 life is exceeded
- brinelling from static overload or hammer blows during mounting
Selection pitfalls — read before you substitute
- At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
- At 50 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
- Sealed self-aligning bearings tolerate less misalignment than open ones: keep static misalignment under roughly 1° on 2210-E-2RS1KTN9 to avoid seal-lip binding.
- The K suffix means a 1:12 tapered bore: 2210-E-2RS1KTN9 is not a drop-in for the straight-bore version — it needs a tapered shaft or an H-series adapter sleeve.
- The E-2RS1KTN9 suffix on 2210-E-2RS1KTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 4800 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- The spherical outer raceway lets 2210-E-2RS1KTN9 tolerate shaft deflection, but it does not increase thrust capacity — combined loads still need an angular-contact or deep-groove bearing.
Frequently asked questions
What are the dimensions of 2210-E-2RS1KTN9?
SKF 2210 E-2RS1KTN9 measures 50 mm bore × 90 mm OD × 23 mm width (1.969 × 3.543 × 0.906 in), mass about 570 g. It has two contact rubber seals (2RS1) and a lifetime grease fill.
How does the bore code in 2210 work?
The final two digits of 2210 are bore code 10, multiplied by 5 to give 50 mm.
How much misalignment can 2210-E-2RS1KTN9 tolerate?
Self-aligning ball bearings tolerate roughly 2–3° of static misalignment for open executions; sealed 2RS1 variants like 2210-E-2RS1KTN9 allow less (about 1°) because the seal lip binds first.
Can 2210-E-2RS1KTN9 take axial load?
A self-aligning ball bearing can carry some axial load in addition to radial load, but its axial capacity is lower than an angular-contact bearing of the same envelope. Use it where misalignment, not thrust, is the main requirement.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.