2211-EKTN9 bearing: complete specifications & equivalents
The 2211-EKTN9 is a ISO 15 radial bearing sized 55 x 100 x 25 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | SKF |
| Bore diameter d | 55 mm |
| Outer diameter D | 100 mm |
| Width B | 25 mm |
| Material | GCr15 |
| Seal / shield | open |
| Internal clearance | CN |
| Tolerance class | P0 |
| Cage | polymer (PA66 glass-fibre reinforced) |
| Basic dynamic load rating C | 39 kN |
| Basic static load rating C0 | 13.4 kN |
| Fatigue load limit Pu | 0.7 kN |
| Reference speed (thermal) | 12000 rpm |
| Limiting speed (mechanical) | 8500 rpm |
| Operating temperature | -40 to +120 °C |
| Mass | 810 g |
| Manufacturer designation | 2211 EKTN9 |
| Standard | ISO 15 |
| Catalog version | SKF PUB BU/P1 17000/1 EN (Oct 2018) |
| Last verified | 2026-09-27 |
Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-27
Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.
Dimensions in inches & 2200-series range
| Bore d | 2.165 in |
|---|---|
| Outer diameter D | 3.937 in |
| Width B | 0.984 in |
| ISO bore code | 11 |
| Radial section height (D−d)/2 | 22.5 mm |
| Smallest bore in 2200-series | 10 mm |
| Largest outer diameter in 2200-series | 200 mm |
| Width range across 2200-series | 14–53 mm |
| Bore position in 2200-series (smallest first) | 12 of 23 |
| Bore above smallest 2200-series size | 45 mm |
Cross references & equivalents
| Equivalent model | Brand | Match level | Note |
|---|---|---|---|
| 2211 | NTN | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 55×100×25 mm envelope per ISO 15; catalogue load ratings differ by >10% — re-rate the application before substituting. |
| 2211-E-2RS1TN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 27.6/10.6 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2211-E-2RS1KTN9 | SKF | partial Main dimensions match; tolerances, seals or internal clearance differ. | Same 55×100×25 mm envelope, but catalogue C/C0 differ between executions (39/13.4 kN vs 27.6/10.6 kN) — boundary dimensions match, not a load-rating equivalent. |
| 2211-ETN9 | SKF | full Dimensions and internal design equivalent — standard interchange. | Same 55×100×25 mm envelope with catalogue ratings within 10 %; 2211 ETN9 is the glass-fibre PA66 cage, open arrangement execution of this size — boundary dimensions interchangeable, only the seal/cage/bore execution differs. |
Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.
How the 2211-EKTN9 model number is decoded
The 22xx series is the wide light-section self-aligning ball bearing (ISO dimension series 22). the last two digits encode the bore: 2211 carries code 11 = 55 mm (code × 5). Envelope 55×100×25 mm (2.165×3.937×0.984 in) with a 22.5 mm radial section height, C 39 kN, C0 13.4 kN and Pu 0.7 kN. The open 2211 EKTN9 carries no shields or seals and relies on application lubrication and external sealing. The EKTN9 suffix identifies the glass-fibre-reinforced polyamide 66 cage execution. The K suffix marks a 1:12 tapered bore for direct mounting on a tapered shaft or with an adapter sleeve. Reference (thermal) speed 12000 r/min, limiting speed 8500 r/min, catalogue mass 810 g.
Typical equipment & failure modes
Common applications
- industrial fans and blowers
- woodworking machinery
- pump shafts with mild misalignment
- material-handling equipment
Known failure patterns
- lubricant starvation where no regreasing interval is maintained
- contamination wear when the open arrangement is used without adequate external sealing
- incorrect sleeve tightening that leaves the tapered bore loose or over-expanded, changing internal clearance
- adapter-sleeve fretting when the sleeve is not locked against the shaft shoulder
- rolling-contact fatigue spalling once the catalogue L10 life is exceeded
- brinelling from static overload or hammer blows during mounting
Selection pitfalls — read before you substitute
- At 55 mm bore, C3 clearance is the safe choice when interference fits plus temperature rise consume the CN clearance; a hot tight bearing with no residual clearance fails fast.
- Fillet radii must clear the 2211-EKTN9 chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- On a sleeve-mounted 2211-EKTN9, lock the sleeve against the shaft shoulder; a loose sleeve creeps and frets both the shaft and the bore.
- The EKTN9 suffix on 2211-EKTN9 denotes a glass-fibre-reinforced polyamide 66 cage: quiet and light at the 8500 r/min limiting speed, but it softens above roughly 120 °C — check the oil temperature in hot drives.
- Fillet radii must clear the 2211-EKTN9 chamfer so the 25 mm-wide ring seats square; an oversized shaft radius creates point contact on the ring face.
- Self-aligning ball bearings tolerate up to roughly 2–3° of static misalignment, but the sealed 2211-EKTN9 (2RS1) allows less — the lip seal binds before the spherical raceway does.
Frequently asked questions
What are the dimensions of 2211-EKTN9?
SKF 2211 EKTN9 measures 55 mm bore × 100 mm OD × 25 mm width (2.165 × 3.937 × 0.984 in), mass about 810 g. It is open, with no shields or seals.
How does the bore code in 2211 work?
The final two digits of 2211 are bore code 11, multiplied by 5 to give 55 mm.
Which fits should I use for 2211-EKTN9?
With a rotating inner ring use roughly k5 on the shaft and H7 in the 100 mm housing; reverse the interference if the outer ring rotates.
How heavy is 2211-EKTN9?
Catalogue mass is 810 g for 2211 EKTN9; seal and cage executions of the same envelope differ by a few grams.
Reviewed & verified by the MPN Base engineering desk against source catalog SKF PUB BU/P1 17000/1 EN (Oct 2018) on 2026-09-27. Read our editorial & correction policy.