2216K bearing: complete specifications & equivalents
The 2216K is a ISO 15 radial bearing sized 80 x 140 x 33 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 80 mm |
| Outer diameter D | 140 mm |
| Width B | 33 mm |
| Seal / shield | open |
| Basic dynamic load rating C | 49 kN |
| Basic static load rating C0 | 19.9 kN |
| Fatigue load limit Pu | 1.3 kN |
| Limiting speed (mechanical) | 4000 rpm |
| Mass | 2020 g |
| Manufacturer designation | 2216SK |
| Standard | ISO 15 |
| Catalog version | CAT. No. 2203-3/E 2024 |
| Last verified | 2026-09-25 |
Source: catalog reference (CAT. No. 2203-3/E 2024) · extracted 2026-09-25
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (CAT. No. 2203-3/E 2024); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 2200-series range
| Bore d | 3.15 in |
|---|---|
| Outer diameter D | 5.512 in |
| Width B | 1.299 in |
| ISO bore code | — |
| Radial section height (D−d)/2 | 30 mm |
| Smallest bore in 2200-series | 10 mm |
| Largest outer diameter in 2200-series | 200 mm |
| Width range across 2200-series | 14–53 mm |
| Bore position in 2200-series (smallest first) | 17 of 23 |
| Bore above smallest 2200-series size | 70 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 2216K model number is decoded
In the 2200-series (ISO 15 dimension series) the leading digits 22 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2216 carries bore code 16 = 80 mm. Outside diameter 140 mm and width 33 mm follow the ISO 15 general plan. The K suffix denotes a 1:12 tapered bore for mounting on an adapter sleeve or tapered shaft seat; the cylindrical-bore equivalent is 2216. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.
Typical equipment & failure modes
Common applications
- hoist, winch and crane drums
- heavy conveyor drive shafts
- pulp, paper and steel mill machinery
- heavy industrial drive shafts
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- edge loading and stress concentration from excessive misalignment beyond the allowable angle
- raceway smearing under marginal lubrication at start-up
Selection pitfalls — read before you substitute
- Mount this 80 mm bore bearing by heating the inner ring (induction heater, max 120 °C) — never drive it home through the outer ring or balls, that brinells the raceways.
- The 22xx wide-section at 80 mm bore adds load capacity through increased 33 mm width; the wider ring needs a wider housing seat and may reduce limiting speed versus a 1216.
- Tapered-bore 2216K requires a matching adapter sleeve (e.g. H2xx for small bores, H3xx for larger); verify the sleeve bore code matches the 80 mm shaft before ordering.
- The adapter sleeve adds length and a small radial step; check that the housing bore and shaft shoulder clear the sleeve nut and that the withdrawal nut is accessible for future dismounting.
- Self-aligning ball bearings have lower axial load capacity than same-size angular-contact or tapered-roller bearings; verify the axial component is within the Y-factor limits for 2216K.
Frequently asked questions
What are the dimensions of a 2216K self-aligning ball bearing?
A 2216K self-aligning ball bearing has a 80 mm bore, 140 mm outer diameter and 33 mm width, per ISO 15 boundary dimensions. The K suffix indicates a 1:12 tapered bore for adapter-sleeve mounting; the cylindrical-bore version is 2216.
How does the 2216 bore code work?
The last two digits of 2216 are bore code 16, giving 16 × 5 = 80 mm bore. The 140 mm outside diameter and 33 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the K suffix mean on 2216K?
The K suffix denotes a 1:12 tapered bore for mounting with an adapter sleeve. The cylindrical-bore equivalent is 2216. Adapter sleeves are sold separately and must match the bore code.
How does the 2200 compare with other self-aligning series at the same 80 mm bore?
The 22xx is the wide light section: 140×33 mm with a 30.0 mm radial section at 80 mm bore, wider than a 1216 for higher load capacity at the cost of speed.
Reviewed & verified by the MPN Base engineering desk against source catalog CAT. No. 2203-3/E 2024 on 2026-09-25. Read our editorial & correction policy.