2315 bearing: complete specifications & equivalents
The 2315 is a ISO 15 radial bearing sized 75 x 160 x 55 mm (bore x OD x width). Verify dimensions against the official catalog before ordering.
Specification table
| Parameter | Value |
|---|---|
| Brand | NTN |
| Bore diameter d | 75 mm |
| Outer diameter D | 160 mm |
| Width B | 55 mm |
| Seal / shield | open |
| Basic dynamic load rating C | 125 kN |
| Basic static load rating C0 | 43 kN |
| Fatigue load limit Pu | 1.8 kN |
| Limiting speed (mechanical) | 3400 rpm |
| Mass | 4780 g |
| Manufacturer designation | 2315S |
| Standard | ISO 15 |
| Catalog version | CAT. No. 2203-3/E 2024 |
| Last verified | 2026-09-25 |
Source: catalog reference (CAT. No. 2203-3/E 2024) · extracted 2026-09-25
Parameters extracted from the official NTN Ball and Roller Bearings catalogue (CAT. No. 2203-3/E 2024); NTN® is a trademark of NTN Corporation, used here for identification only — mpnbase is not an authorized NTN distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at ntnglobal.com.
Dimensions in inches & 2300-series range
| Bore d | 2.953 in |
|---|---|
| Outer diameter D | 6.299 in |
| Width B | 2.165 in |
| ISO bore code | 15 |
| Radial section height (D−d)/2 | 42.5 mm |
| Smallest bore in 2300-series | 10 mm |
| Largest outer diameter in 2300-series | 215 mm |
| Width range across 2300-series | 17–73 mm |
| Bore position in 2300-series (smallest first) | 16 of 21 |
| Bore above smallest 2300-series size | 65 mm |
Cross references & equivalents
No verified interchange data yet. Send an inquiry and our team will confirm equivalents manually.
How the 2315 model number is decoded
In the 2300-series (ISO 15 dimension series) the leading digits 23 mark a double-row self-aligning ball bearing and the last two digits encode the bore: 2315 carries bore code 15 = 75 mm. Outside diameter 160 mm and width 55 mm follow the ISO 15 general plan. The cylindrical bore fits directly on a machined shaft seat; a tapered-bore K variant is available for adapter-sleeve mounting. Two rows of balls run on a common sphered outer raceway, allowing the inner ring to pivot and compensate for shaft deflection or housing misalignment.
Typical equipment & failure modes
Common applications
- conveyor and material handling drives
- textile and printing machine spindles
- paper mill and processing equipment shafts
- industrial electric motor shafts
Known failure patterns
- contamination wear from dust and dirt ingress through the open arrangement
- lubricant starvation when no regreasing interval is maintained
- rolling-contact fatigue spalling after the rated L10 life is exceeded
- cage wear or fracture from sustained vibration or shock loading
Selection pitfalls — read before you substitute
- Temperature rise and interference fits consume internal clearance on this 75 mm bore: a CN bearing on a tight, hot shaft can lose all residual clearance — size 2315 with C3 for those conditions.
- The 23xx heavy wide-section at 75 mm bore is built for high-load, lower-speed duty; specifying it in a high-rpm application gives excess heat and short grease life — use 12/13 there.
- The open 2315 has no lubricant retention: grease escapes and contaminants migrate straight into the 75×160×55 mm raceway, so specify a sealed arrangement for dusty or washdown duty.
- Open bearings tolerate the highest speeds in the 2300-series but need a defined regreasing interval; run-to-failure lubrication is the dominant cause of early failure in open 2315 units.
- Shaft and housing fillets must clear the bearing chamfer so the 55 mm-wide ring seats square; provide an undercut or withdrawal groove instead of relying on an oversized radius.
Frequently asked questions
What are the dimensions of a 2315 self-aligning ball bearing?
A 2315 self-aligning ball bearing has a 75 mm bore, 160 mm outer diameter and 55 mm width, per ISO 15 boundary dimensions. This is the cylindrical-bore version; a tapered-bore K variant is available for adapter-sleeve mounting.
How does the 2315 bore code work?
The last two digits of 2315 are bore code 15, giving 15 × 5 = 75 mm bore. The 160 mm outside diameter and 55 mm width follow the ISO 15 diameter series, not the bore code alone.
What does the open suffix mean on 2315?
A bare 2315 designation means open: no shields or seals, normal CN radial clearance and P0 normal tolerance unless further suffixes are ordered. The application must supply and retain the lubrication.
How does the 2300 compare with other self-aligning series at the same 75 mm bore?
The 23xx is the wide heavy section: 160×55 mm, 42.5 mm radial section at 75 mm bore — the highest-capacity double-row self-aligning option here, aimed at lower-speed, high-load shafts.
Reviewed & verified by the MPN Base engineering desk against source catalog CAT. No. 2203-3/E 2024 on 2026-09-25. Read our editorial & correction policy.