OH-3076-H adapter sleeve: complete specifications & mounting data

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 23.1 adapter sleeves for metric shafts) · extracted 2026-09-30

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018), ch. 23.1 adapter sleeves for metric shafts); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the OH-3076-H model number is decoded

oil reaches the interface through the M 6 duct connection into distribution grooves, so the 35,500 g sleeve can be floated off the 360 mm shaft instead of being pressed or pulled the seat taper is 1:12, so each millimetre of axial drive-up removes about 1/12 mm of radial clearance; one turn of the HM 3076 nut on the Tr 380x5 thread advances 5 mm and takes out roughly 0.417 mm of clearance the OD-to-bore ratio is 1.18: the 450 mm sleeve OD is only 35 mm of section beyond the 380 mm seat, leaving room for the bearing outer ring without enlarging the housing bore the HM 3076 lock nut carries size index 3076, matching the bore-code family of the 380 mm seat; the nut engages the Tr 380x5 sleeve thread over its full width for controlled drive-up the catalogue pairs this seat with the HMV 76E hydraulic nut (size 76); at 35,500 g the sleeve and bearing together are too heavy to seat reliably with a hook spanner alone the 360 mm shaft size is the domain of rolling-mill, paper-machine and marine equipment — the oil ducts and the HMV 76E hydraulic nut are essential at this scale reading OH 3076 H: OH identifies the oil-injection sleeve — oil is pumped through the M 6 duct connection into interface grooves, so the 35,500 g sleeve floats on and off without pullers or heat the OH30 designation block places it in the oil-injection OH 30 range for 230..K spherical roller bearings — every sleeve in the block uses the same bore-code logic, and here the 380 mm tapered bore matches the K-suffix bearing it is ordered for hardware on this row: the HM 3076 lock nut and the MS 3080-76 locking clip; SKF lists the HMV 76E hydraulic nut for mounting and dismounting typical applications include textile machine roller shafts, electric motor and generator shafts and woodworking saw and planer spindles adapter sleeves earn their place wherever a tapered-bore bearing must sit at any axial position on a plain shaft — here a 380 mm bore bearing on a 360 mm shaft in woodworking saw and planer spindles the sleeve lets the designer use a plain, unstepped shaft and still locate the bearing positively; only one shoulder is needed, opposite the HM 3076 nut ordering digest — OH 3076 H: 360 mm plain shaft to 380 mm tapered bore, sleeve 450 mm OD and 193 mm wide, thread Tr 380x5, supplied with HM 3076 nut with MS 3080-76 clip, drive-up tool HMV 76E; listed mass is 35,500 g

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• interchanging nut families (KM vs KMFE, MB vs MS) across executions loses locking reliability even when the thread appears to fit
• mounting without a fixed abutment lets the bearing walk axially; the sleeve needs a shaft shoulder opposite the lock nut
• neglecting the catalogue axial displacement value leaves the bearing either loose on the taper or preloaded hot in service