YAR-207-104-2F bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the YAR-207-104-2F model number is decoded

YAR 207-104-2F is SKF's 31.75 mm-bore grub-screw insert bearing with the inner ring extended on both sides in the YAR2 series — a Y-bearing with a spherically ground outside surface for static self-alignment inside a matching SKF Y-housing, boundary dimensions 31.75x72x42.9 mm. Wide-inner-ring deep-groove ball geometry carries the load: the extended inner ring gives the shaft grip and the seal lands, while the outer ring stays narrow and spherically ground on its outside surface. the YAR prefix names SKF grub-screw Y-bearings: two set screws in the extended inner ring lock the shaft at a 120 deg angle, and the inner ring extends symmetrically on both sides. the three-digit -104 tail codes the bore in inches for inch-shaft bearings: 1 whole inch 4/16 in = 31.75 mm (first digit whole inches, next two sixteenths of an inch). suffix -2F means an NBR rubber contact seal plus a plain pressed-steel flinger on EACH side: the lip rides the extended inner ring while the flinger sheds coarse contamination before it reaches the lip. Envelope 31.75x72x42.9 mm (1.25x2.835x1.689 in), outer ring 19 mm wide, C 25.5 kN, C0 15.3 kN, Pu 0.655 kN. The catalogue publishes a single speed ceiling, the limiting speed: 5,300 r/min; mass 500 g. Width accounting on this execution: 42.9 mm overall and 19 mm outer-ring width leave the housing designer 23.9 mm of inner-ring projection to accommodate the locking arrangement. At the printed limiting speed of 5,300 r/min the mean diameter dm = 51.875 mm implies dn about 2.75x10^5 mm.r/min — the speed-demand figure used when comparing this insert with open deep-groove sizes of the same bore. Imperial procurement cross-check: 1.25 in bore, 2.835 in OD, 1.689 in overall width; the 500 g mass converts to 0.500 kg (17.6 oz) for the bill of materials. Rating split for the maintenance file: dynamic 25.5 kN (L10), static 15.3 kN (s0 shock check), fatigue 0.655 kN (adjusted life) — three separate uses for YAR 207-104-2F, none interchangeable with another. Fillet discipline: the printed r_min 1 mm limit means shaft and housing fillets must stay under that radius; a fillet that bottoms the 31.75x72 mm insert on its chamfer tilts the whole spherical seat. Both-sides sealed order-number note: the two set screws clamp through dimpled recesses in the extended inner ring; tighten alternately to the catalogue procedure and retighten after the first run-in period, because the -2F flingers keep dust out but cannot compensate for a screw that walked loose. Set-screw geometry on this size: the two 120 deg screws bear on the 31.75 mm shaft inside the 42.9 mm total width while the outer ring is only 19 mm wide, leaving the extended ring to carry the screw points clear of the ball track.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Replacement discipline: a YAR insert is not interchangeable with an eccentric-collar unit of the same envelope — the shaft may need spot-facing or collar space that does not exist.
• The 25.4 mm s1 dimension is the screw seating geometry inside the 23.9 mm of extended inner ring; a shaft step that crowds that side prevents the screws reaching the shaft squarely.
• Do not specify the 31.75 mm grub-screw insert for a shaft harder than about 45 HRC without dimples: the screw points skate on hard surfaces and the unit creeps regardless of tightening torque.
• Ordering discipline for the 31.75 mm size: the chapter lists several executions side by side (YAR2 locking style x seal package x application variant); a bare-number substitution needs a fresh dimension, speed and rating check rather than a like-for-like assumption.