YAR-209-112-2F bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the YAR-209-112-2F model number is decoded

YAR 209-112-2F is SKF's 44.449999999999996 mm-bore grub-screw insert bearing with the inner ring extended on both sides in the YAR2 series — a Y-bearing with a spherically ground outside surface for static self-alignment inside a matching SKF Y-housing, boundary dimensions 44.449999999999996x85x49.2 mm. Wide-inner-ring deep-groove ball geometry carries the load: the extended inner ring gives the shaft grip and the seal lands, while the outer ring stays narrow and spherically ground on its outside surface. the YAR prefix names SKF grub-screw Y-bearings: two set screws in the extended inner ring lock the shaft at a 120 deg angle, and the inner ring extends symmetrically on both sides. the three-digit -112 tail codes the bore in inches for inch-shaft bearings: 1 whole inch 12/16 in = 44.45 mm (first digit whole inches, next two sixteenths of an inch). suffix -2F means an NBR rubber contact seal plus a plain pressed-steel flinger on EACH side: the lip rides the extended inner ring while the flinger sheds coarse contamination before it reaches the lip. Envelope 44.449999999999996x85x49.2 mm (1.75x3.346x1.937 in), outer ring 22 mm wide, C 33.2 kN, C0 21.6 kN, Pu 0.915 kN. The catalogue publishes a single speed ceiling, the limiting speed: 4,300 r/min; mass 690 g. Grease-life arithmetic is dominated by speed: at dn approx 2.78x10^5 the sealed-for-life fill is planned for the catalogue's grease-life regime, which is why the limiting speed and the relubrication interval move together, and high-temperature mounts shorten both even when load is light. Spherical-seat note in numbers: the 85 mm OD is ground spherical, so the self-aligning pivot happens on a circle roughly pi x 64.725 = 203.34 mm in mean circumference — keep that interface greased, because corrosion locking turns the pivot into a fixed misaligned mount. Pitch-diameter arithmetic: dm = (44.449999999999996+85)/2 = 64.725 mm; at the 4,300 r/min limiting speed the ball set runs at dn approx 2.78x10^5, reduced from an open bearing mainly by seal lip friction and the life-long grease fill. Load balance for documentation: C0 21.6 kN against C 33.2 kN gives a 0.651 ratio; mounted-unit positions with shock and standstill loading are normally checked on C0, while conveyor and fan duty are evaluated on the L10 figure. Rating split for the maintenance file: dynamic 33.2 kN (L10), static 21.6 kN (s0 shock check), fatigue 0.915 kN (adjusted life) — three separate uses for YAR 209-112-2F, none interchangeable with another. Both-sides sealed order-number note: the two set screws clamp through dimpled recesses in the extended inner ring; tighten alternately to the catalogue procedure and retighten after the first run-in period, because the -2F flingers keep dust out but cannot compensate for a screw that walked loose. Service tip for YAR-209-112-2F: dimpled or drilled shaft spots under the screw points are sometimes specified on shock duty, but the standard mounting relies on point indentation alone — never substitute longer screws that reach the 20.275 mm radial section.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• Replacement discipline: a YAR insert is not interchangeable with an eccentric-collar unit of the same envelope — the shaft may need spot-facing or collar space that does not exist.
• Do not specify the 44.449999999999996 mm grub-screw insert for a shaft harder than about 45 HRC without dimples: the screw points skate on hard surfaces and the unit creeps regardless of tightening torque.
• The 30.2 mm s1 dimension is the screw seating geometry inside the 27.2 mm of extended inner ring; a shaft step that crowds that side prevents the screws reaching the shaft squarely.
• Ordering discipline for the 44.449999999999996 mm size: the chapter lists several executions side by side (YAR2 locking style x seal package x application variant); a bare-number substitution needs a fresh dimension, speed and rating check rather than a like-for-like assumption.