YAR-213-208-2RF bearing: complete specifications & equivalents

Specification table

Source: catalog reference (SKF PUB BU/P1 17000/1 EN (Oct 2018)) · extracted 2026-09-28

Parameters extracted from the official SKF Rolling Bearings catalogue (SKF PUB BU/P1 17000/1 EN (Oct 2018)); SKF® and SKF Explorer® are trademarks of AB SKF, used here for identification only — mpnbase is not an authorized SKF distributor. Boundary dimensions are ISO 15 interchangeable; current production values may differ, verify at skf.com.

Cross references & equivalents

Interchange levels: full standard interchange · partial verify parameters · verify manual confirmation required. Links resolve to the equivalent model's specification page where available.

How the YAR-213-208-2RF model number is decoded

The YAR2 series order number YAR 213-208-2RF is a SKF insert bearing (Y-bearing) for a 63.5 mm (2.5 in) shaft: grub-screw insert bearing with the inner ring extended on both sides, built to the ISO 15 diameter-series envelope with a sphered OD of 120 mm. Inside is a sealed deep-groove ball set with an extended inner ring, two set screws 120 deg apart doing the shaft locking, and the sphered outer ring providing the unit's static alignment pivot. reading the YAR basic designation: set-screw shaft locking with the screws spaced 120 deg apart; YAR carries the symmetric, both-sides-extended inner ring. inch bore code -208 decodes as 2" +8/16, i.e. 63.5 mm; the metric coded size YAR 213 shares the same envelope but its bore is the metric value, not this one. -2RF means an NBR contact lip plus a rubber-coated flinger at both sides, the catalogue step above -2F for wet, abrasive or washed-down environments. Envelope 63.5x120x68.3 mm (2.5x4.724x2.689 in), outer ring 27 mm wide, C 57.2 kN, C0 40 kN, Pu 1.7 kN. The catalogue publishes a single speed ceiling, the limiting speed: 1,600 r/min; mass 1900 g. Load balance for documentation: C0 40 kN against C 57.2 kN gives a 0.699 ratio; mounted-unit positions with shock and standstill loading are normally checked on C0, while conveyor and fan duty are evaluated on the L10 figure. Inner-geometry cross-reference: the catalogue shoulder diameters (d1 82.5 mm) set the shaft-abutment and sleeve limits; an abutment larger than these numbers contacts the seal or the rubberized flinger. Envelope arithmetic: the radial section from 63.5 mm bore to 120 mm OD is 28.25 mm; dividing C 57.2 kN by that section gives 2.025 kN per section millimetre, and the 68.3 mm overall width is 2.418x the section. Bore-to-OD planning: OD 120 over bore 63.5 is a 1.89x step, while bore/overall-width gives 0.93; the spherical seat in the matching Y-housing must be specified to the 120 mm OD, not to a cylindrical housing bore. Capacity density: 57.2 kN from 1.900 kg of bearing steel is about 30.105 kN per kilogram, and per width millimetre the 68.3 mm unit carries 0.837 kN of dynamic capacity. Rubberized-flinger note: the -2RF coated throwers are vulcanized assemblies — never lever or hammer against the flinger when mounting, and press only on the inner ring when the bearing is fitted loose before the housing cap closes, or the flinger lip folds inward and grinds on the inner ring. Service tip for YAR-213-208-2RF: dimpled or drilled shaft spots under the screw points are sometimes specified on shock duty, but the standard mounting relies on point indentation alone — never substitute longer screws that reach the 28.25 mm radial section.

Typical equipment & failure modes

Selection pitfalls — read before you substitute

• The 42.9 mm s1 dimension is the screw seating geometry inside the 41.3 mm of extended inner ring; a shaft step that crowds that side prevents the screws reaching the shaft squarely.
• Replacement discipline: a YAR insert is not interchangeable with an eccentric-collar unit of the same envelope — the shaft may need spot-facing or collar space that does not exist.
• Do not specify the 63.5 mm grub-screw insert for a shaft harder than about 45 HRC without dimples: the screw points skate on hard surfaces and the unit creeps regardless of tightening torque.
• The 57.2/40 kN figures belong specifically to YAR 213-208-2RF; HV stainless, AG agricultural and VE495 zinc-plated variants of the same envelope publish derated values, so write the complete order number including suffixes on the purchase and maintenance records.